Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VANDAR® 2100 - PBT - Celanese

Material Data Center offers the following functions for VANDAR® 2100:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Vandar datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Informação do produto
Vandar 2100 is a polyester alloy designed to offer maximum impact strength at room and low temperatures. This unfilled compound is characterized by outstanding chemical resistance, dimensional stability, paintability, and toughness.

Flammability at thickness h (1.6 mm)HB-
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 5.5 cm³/10min ISO 1133
Temperatura 250 °C -
Carga 5 kg -
Contração após a moldagem, paralelo 1.9 % ISO 294-4, 2577
Contração após a moldagem, perpendicular 1.9 % ISO 294-4, 2577
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 1700 MPa ISO 527
Tensão no escoamento 40 MPa ISO 527
Deformação no escoamento 4 % ISO 527
Deformação nominal na ruptura >50 % ISO 527
Resistência ao impacto Charpy , +23°C N kJ/m² ISO 179/1eU
Resistência ao impacto Charpy, -30°C N kJ/m² ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C 80 kJ/m² ISO 179/1eA
Res. impacto Charpy c/entalhe, -30°C 16 kJ/m² ISO 179/1eA
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 225 °C ISO 11357-1/-3
Temp. de transição vítrea, 10°C/min 60 °C ISO 11357-1/-2
Temperatura de deflexão térmica, 1.80 MPa 50 °C ISO 75-1/-2
Temperatura de deflexão térmica, 0.45 MPa 110 °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 137 °C ISO 306
Coef. de expansão térmica linear, paralelo 130 E-6/K ISO 11359-1/-2
Flamabilidade a espessura h HB class IEC 60695-11-10
Espessuras do tubo de teste 1.6 mm -
Propriedades elétricasValorUnidadeMétodo de ensaio
ISO Dados
Constante dielétrica, 100Hz 4 - IEC 62631-2-1
Constante dielétrica, 1MHz 3.6 - IEC 62631-2-1
Fator de dissipação dielétrica, 100Hz 70 E-4 IEC 62631-2-1
Fator de dissipação dielétrica, 1MHz 200 E-4 IEC 62631-2-1
Resistividade volumétrica específica 1E12 Ohm*m IEC 62631-3-1
Resistividade superficial específica 1E14 Ohm IEC 62631-3-2
Resistência elétrica 24 kV/mm IEC 60243-1
Outras propriedadesValorUnidadeMétodo de ensaio
Absorção de água 0.45 % Sim. to ISO 62
Absorção de umidade 0.2 % Sim. to ISO 62
Densidade 1230 kg/m³ ISO 1183
Diagrama
Módulo de cisalhamento dinâmico - temperatura , VANDAR® 2100, PBT, Celanese
Tensão - deformação , VANDAR® 2100, PBT, Celanese
Módulo secante - deformação , VANDAR® 2100, PBT, Celanese
Características
Processamento
Moldagem por injeção, Outros tipos de extrusão
Forma de entrega
Granulos
Características especiais
Alto impacto., Estável contra o calor
Resistência Química
Resistência química geral
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África
Outras informações
Moldagem por injeção
To avoid hydrolytic degradation during processing, Vandar resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30°F (-34°C) at 250°F (121°C) for 4 hours.
Rear Temperature 450-480(230-250) deg F (deg C)
Center Temperature 460-490(235-255) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 470-510(240-265) deg F (deg C)
Melt Temperature 470-510(240-265) deg F (deg C)
Mold Temperature 100-200(40-95 deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Moderate
Injection Speed Fast

Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.