Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin 1110F - Asia - PEI - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin 1110F - Asia:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Informação do produto
Enhanced flow Polyetherimide (Tg 217C). ECO Conforming. US FDA and EU Food Contact compliant, NSF 51 listing. UL94 V0 and 5VA listing. Effective June 2007, this grade will no longer be supported with biocompatibility information and should not be used for medical applications which require biocompatibility. Alternative grade HU1110.

UL Yellow Card Link E121562-101048269
Características de processamento/físicasValorUnidadeMétodo de ensaio
ASTM Dados
Índice de fluidez, MFI 16 g/10min ASTM D 1238
Temperatura 337 °C -
Carga 6.6 kg -
Propriedades mecânicasValorUnidadeMétodo de ensaio
ASTM Dados
Módulo de tração 3720 MPa ASTM D 638
Resistência à tração no escoamento 110 MPa ASTM D 638
Deformação na ruptura 70 % ASTM D 638
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Flamabilidade a espessura h V-2 class IEC 60695-11-10
Espessuras do tubo de teste 0.4 mm -
Flamabilidade 5V a espessura h 5VA class IEC 60695-11-20
Espessuras do tubo de teste 3.0 mm -
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1360 kg/m³ ASTM D 792
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 150 °C -
Pré-secagem - tempo 4 - 6 h -
Umidade do processamento ≤0.02 % -
Temperatura da massa 350 - 400 °C -
Temperatura do molde 135 - 165 °C -
Zona 1 330 - 400 °C -
Zona 2 340 - 400 °C -
Zona 3 345 - 400 °C -
Velocidade de parafuso 40 - 70 rpm -
Contrapressão 0.3 - 0.7 MPa -
Características
Processamento
Moldagem por injeção
Certifications
Contacto com alimentos, Aprovação de alimentos FDA 21 CFR
Disponibilidade regional
Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.