Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ROTEC® ABS 1001 GF17 - ABS-GF17 - Romira GmbH

Material Data Center offers the following functions for ROTEC® ABS 1001 GF17:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Rotec datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez, MFI 10 g/10min ISO 1133
Temperatura 220 °C -
Carga 10 kg -
Contração após a moldagem, paralelo 0.3 % ISO 294-4, 2577
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 5650 MPa ISO 527
Resistência à tração 80 MPa ISO 527
Deformação na ruptura 5 % ISO 527
Módulo de flexão, 23°C 5000 MPa ISO 178
Resistência à flexão 105 MPa ISO 178
Resistência ao impacto Charpy, +23°C 20 kJ/m² ISO 179/1eU
Resistência ao impacto Charpy, -30°C 18 kJ/m² ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C 7 kJ/m² ISO 179/1eA
Res. impacto Charpy c/entalhe, -30°C 5 kJ/m² ISO 179/1eA
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica, 1.80 MPa 89 °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 105 °C ISO 306
Flamabilidade a 1.5mm esp. nom. HB class IEC 60695-11-10
Espessuras do tubo de teste 1.5 mm -
Cartão Amarelo (yellow card) disponível sim - -
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1160 kg/m³ ISO 1183
Características
Processamento
Moldagem por injeção
Características especiais
Estável contra o calor
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.