Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RTP 300 FR - PC - RTP Company

Material Data Center offers the following functions for RTP 300 FR:
unit conversion, PDF datasheet print, comparison with other plastics, application examples, CAE Interfaces

Check here, which other RTP datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ASTM Dados
Índice de fluidez, MFI 11 g/10min ASTM D 1238
Temperatura 300 °C -
Carga 1.2 kg -
Contração após a moldagem, paralelo 0.0065 mm/mm ASTM D 955
Propriedades mecânicasValorUnidadeMétodo de ensaio
ASTM Dados
Módulo de tração 2413 MPa ASTM D 638
Resistência à tração 62.1 MPa ASTM D 638
Módulo de flexão 2413 MPa ASTM D 790
Resistência à flexão 96.5 MPa ASTM D 790
Dureza Rockwell R 118 - ASTM D 785
Impacto Izod com entalhe, 1/8 in 427 J/m ASTM D 256
Propriedades térmicasValorUnidadeMétodo de ensaio
ASTM Dados
UL94 flamabilidade V-0 - UL 94
Espessuras do tubo de teste 1.59 mm -
DTUL @ 66 psi 138 °C ASTM D 648
DTUL @ 264 psi 132 °C ASTM D 648
Propriedades elétricasValorUnidadeMétodo de ensaio
ASTM Dados
Resistência elétrica, tempo curto 16.7 kV/mm ASTM D 149
Fator de dissipação dielétrica, 1 MHz 0.01 - ASTM D 150
Constante dielétrica, 1 MHz 3 - ASTM D 150
Outras propriedadesValorUnidadeMétodo de ensaio
Absorção de água, 24hr 0.15 % ASTM D 570
Densidade 1230 kg/m³ ASTM D 792
Moisture Content 0.02 % -
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 121 °C -
Pré-secagem - tempo 4 h -
Temperatura da massa 288 - 316 °C -
Temperatura do molde 82.2 - 121 °C -
Pressão de injeção 68.9 - 103 MPa -
Características
Processamento
Moldagem por injeção
Características especiais
Retardante de chama
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.