Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of Novodur® HD-15 - ABS - INEOS Styrolution
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Novodur datasheets, application examples or technical articles are available in Material Data Center
Novodur® HD-15 is in compliance with Pharmacopoeia and Biocompatibility-Tests in Europe and United States as specified below.
However, the biocompatibility tests were recorded on tests specimens of Novodur® HD-15 to show compatibility of the material in general. The biocompatibility-tests listed below are not part of any continuous production control.
European Pharmacopoeia:
The composition of the product complies with the requirements of the European Pharmacopoeia 5th Edition, Chap. 3.2.2.
"Plastic Containers and Closures".
US Pharmacopoeia
Biological Reactivity Tests, USP Plastic Class VI (USP VI)
ISO 10993-5
Biological Evaluation of Medical Devices Part 5: Test for Cytotoxicity
DMF:
A Drug Master File (DMF) has been registered at FDA for Terluran® HD-15. The assigned DMF Number is 18858.
Características de processamento/físicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Índice de fluidez volumétrico, MVR | 15 | cm³/10min | ISO 1133 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura | 220 | °C | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Carga | 10 | kg | - |
Propriedades mecânicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Módulo de tração | 2300 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Tensão no escoamento | 38 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Deformação no escoamento | 2.5 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Deformação nominal na ruptura | 10 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistência ao impacto Charpy , +23°C | 170 | kJ/m² | ISO 179/1eU | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistência ao impacto Charpy, -30°C | 90 | kJ/m² | ISO 179/1eU | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Res. impacto Charpy c/entalhe, +23°C | 14 | kJ/m² | ISO 179/1eA | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Res. impacto Charpy c/entalhe, -30°C | 6 | kJ/m² | ISO 179/1eA |
Propriedades térmicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura de deflexão térmica, 1.80 MPa | 93 | °C | ISO 75-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura de deflexão térmica, 0.45 MPa | 99 | °C | ISO 75-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura de amolecimento Vicat, B | 100 | °C | ISO 306 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Coef. de expansão térmica linear, paralelo | 95 | E-6/K | ISO 11359-1/-2 |
Propriedades elétricas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Constante dielétrica, 100Hz | 2.9 | - | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Constante dielétrica, 1MHz | 2.8 | - | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Fator de dissipação dielétrica, 100Hz | 48 | E-4 | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Fator de dissipação dielétrica, 1MHz | 79 | E-4 | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistividade volumétrica específica | 1E13 | Ohm*m | IEC 62631-3-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistividade superficial específica | 1E13 | Ohm | IEC 62631-3-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Índice comparativo de linha de fuga | 600 | - | IEC 60112 |
Outras propriedades | Valor | Unidade | Método de ensaio |
Absorção de água | 1 | % | Sim. to ISO 62 |
Absorção de umidade | 0.22 | % | Sim. to ISO 62 |
Densidade | 1050 | kg/m³ | ISO 1183 |
Recomendação de processamento Moldagem por injeção | Valor | Unidade | Método de ensaio |
Pré-secagem - temperatura | 80 | °C | - |
Pré-secagem - tempo | 2 - 4 | h | - |
Temperatura da massa | 220 - 260 | °C | - |
Temperatura do molde | 30 - 60 | °C | - |
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 2 - 4 h
PROCESSING
injection molding, Melt temperature, range: 220 - 260 °C
injection molding, Mold temperature, range: 30 - 60 °C
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.