Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Mosten® MA 745 - PP - ORLEN Unipetrol RPA s.r.o.

Material Data Center offers the following functions for Mosten® MA 745:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Mosten datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez, MFI 45 g/10min ISO 1133
Temperatura 230 °C -
Carga 2.16 kg -
Contração após a moldagem, paralelo 2.0 % ISO 294-4, 2577
Contração após a moldagem, perpendicular 2.3 % ISO 294-4, 2577
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 1350 MPa ISO 527
Tensão no escoamento 26 MPa ISO 527
Deformação no escoamento 5 % ISO 527
Deformação na ruptura 30 % ISO 527
Módulo de flexão, 23°C 1400 MPa ISO 178
Módulo de tensão de fluência, 1h 1100 MPa ISO 899-1
Módulo de tensão de fluência, 1000h 540 MPa ISO 899-1
Res. impacto Charpy c/entalhe, +23°C 9 kJ/m² ISO 179/1eA
Dureza Shore D 60 - ISO 7619-1
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 168 °C ISO 11357-1/-3
Temperatura de deflexão térmica, 1.80 MPa 55 °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 151 °C ISO 306
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Temperatura da massa 200 - 280 °C -
Temperatura do molde 20 - 60 °C -
Características
Processamento
Moldagem por injeção
Forma de entrega
Granulos, Cor natural
Características especiais
Antiestático, Alto impacto.
Características
Nucleado, Copolímero
Certifications
Contacto com alimentos, Aprobación del 1935/2004/EG, Aprovação para contacto com alimentos10/2011
Aplicaciones
Embalaje
Disponibilidade regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.