Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Marlex® D139DK - (PE-LLD) - Chevron Phillips Chemical Co. LP

Material Data Center offers the following functions for Marlex® D139DK:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Marlex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades ópticas - Outras propriedades - Propriedades do filme - Recomendação de processamento Extrusão
Any use of this information falls under the rules of our disclaimer.
Informação do produto
METALLOCENE LINEAR LOW DENSITY POLYETHYLENE (mLLDPE).
Características de processamento/físicasValorUnidadeMétodo de ensaio
ASTM Dados
Índice de fluidez, MFI 1 g/10min ASTM D 1238
Temperatura 190 °C -
Carga 2.16 kg -
Propriedades ópticasValorUnidadeMétodo de ensaio
ASTM Dados
Brilho 103 - ASTM D 2457
Haze 9 % ASTM D 1003
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 918 kg/m³ ASTM D 792
Propriedades do filmeValorUnidadeMétodo de ensaio
ASTM Data
Resistência à tração no escoamento, long. 12.8 MPa ASTM D 882
Resistência à tração no escoamento, trans. 9.65 MPa ASTM D 882
Resistência à tração na ruptura, long. 57.2 MPa ASTM D 882
Resistência à tração na ruptura, trans. 45.9 MPa ASTM D 882
Deformação na ruptura, long. 450 % ASTM D 882
Deformação na ruptura, trans. 560 % ASTM D 882
Tipo de extrusão blown - -
Espessura de corpo de prova 0.0254 mm -
Recomendação de processamento ExtrusãoValorUnidadeMétodo de ensaio
Type of extrusion blown - -
Temperatura da massa 204 °C -
Características
Processamento
Extrusão de filme soprado, Extrusão de laminas
Aditivos
Agente antibloqueio
Características especiais
Transparente
Características
Heat Sealable, High Gloss, Copolímero, Copolímero de hexeno
Aplicaciones
Embalaje
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.