Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of XANTAR™ 25 R - PC - Mitsubishi Engineering-Plastics Corporation
Material Data Center offers the following functions for XANTAR™ 25 R:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, cooling time calculation, CAE Interfaces
Check here, which other Xantar datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our
disclaimer.
Processing/Physical Characteristics | 값 | 단위 | 시험규격 |
ISO 데이터 |
용융 부피 - 흐름 속도, MVR |
5 |
cm³/10min |
ISO 1133 |
온도 |
300 |
°C |
- |
하중 |
1.2 |
kg |
- |
성형 수축률, 평행 |
0.6 |
% |
ISO 294-4, 2577 |
용융 밀도 |
1010 |
kg/m³ |
- |
용융 열전도율 |
0.24 |
W/(m K) |
- |
용융 비열용량 |
1710 |
J/(kg K) |
- |
효율적 열전도도 |
1.4E-7 |
m²/s |
- |
이형온도 |
131 |
°C |
- |
기계적 특성 | 값 | 단위 | 시험규격 |
ISO 데이터 |
인장탄성률 |
2300 |
MPa |
ISO 527 |
항복강도 |
60 |
MPa |
ISO 527 |
항복변형률 |
6 |
% |
ISO 527 |
파단시 평균신율 |
>50 |
% |
ISO 527 |
열적 특성 | 값 | 단위 | 시험규격 |
ISO 데이터 |
하중하에서의 변형온도, 1.80 MPa |
130 |
°C |
ISO 75-1/-2 |
비카트 연화 온도, B |
150 |
°C |
ISO 306 |
선형 열팽창 계수, 평행 |
65 |
E-6/K |
ISO 11359-1/-2 |
1.5mm 평균두께에서의 난연성 |
V-2 |
class |
IEC 60695-11-10 |
테스트 두께 |
1.5 |
mm |
- |
Yellow Card 유효한 |
예 |
- |
- |
두께 H인 제품의 난연성 |
V-2 |
class |
IEC 60695-11-10 |
테스트 두께 |
3.0 |
mm |
- |
Yellow Card 유효한 |
예 |
- |
- |
산소지수로서의 난연성 |
26 |
% |
ISO 4589-1/-2 |
전기적 특성 | 값 | 단위 | 시험규격 |
ISO 데이터 |
상대 유전율, 100Hz |
3 |
- |
IEC 62631-2-1 |
상대 유전뮬, 1MHz |
2.9 |
- |
IEC 62631-2-1 |
소산 인자, 100Hz |
6.6 |
E-4 |
IEC 62631-2-1 |
소산 인자, 1MHz |
92 |
E-4 |
IEC 62631-2-1 |
부피 저항 |
>1E13 |
Ohm*m |
IEC 62631-3-1 |
표면 저항 |
>1E15 |
Ohm |
IEC 62631-3-2 |
전기 압력 |
29 |
kV/mm |
IEC 60243-1 |
CTI |
225 |
- |
IEC 60112 |
기타 특성 | 값 | 단위 | 시험규격 |
물에서의 흡수성 |
0.35 |
% |
ISO 62와 유사 |
밀도 |
1200 |
kg/m³ |
ISO 1183 |
물질의 비성질 | 값 | 단위 | 시험규격 |
ISO 데이터 |
점도수 |
63 |
cm³/g |
ISO 307, 1157, 1628 |
테스트 견본 생산 | 값 | 단위 | 시험규격 |
ISO 데이터 |
사출성형: 용융수지온도 |
300 |
°C |
ISO 294 |
사출성형: 금형온도 |
90 |
°C |
ISO 294 |
Processing Recommendation Injection Molding | 값 | 단위 | 시험규격 |
Pre-drying - Temperature |
120 |
°C |
- |
Pre-drying - Time |
4 |
h |
- |
Processing humidity |
≤0.03 |
% |
- |
용융수지온도 |
290 - 320 |
°C |
- |
성형온도 |
80 - 120 |
°C |
- |
Zone 1 |
260 - 280 |
°C |
- |
Zone 2 |
270 - 290 |
°C |
- |
Zone 3 |
280 - 300 |
°C |
- |
Nozzle temperature |
270 - 290 |
°C |
- |
특징
생산 공정
사출 성형, 기타 압출, 중공 성형
인도 유형
펠렛 (입자,알갱이)
부가물
이형제
특별 특성
열안정성, 투명도
지역별 검색
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.