Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VICTREX® PEEK 450CA20 - PEEK-CF20 - Victrex plc

Material Data Center offers the following functions for VICTREX® PEEK 450CA20:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Victrex PEEK datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics단위시험규격
ISO 데이터
성형 수축률, 평행 0.2 % ISO 294-4, 2577
성형 수축률, 수직 0.7 % ISO 294-4, 2577
기계적 특성단위시험규격
ISO 데이터
인장탄성률 19500 MPa ISO 527
파단시 강도 230 MPa ISO 527
파단시 신율 2.1 % ISO 527
굴곡 계수, 23°C 16500 MPa ISO 178
굴곡 강도 340 MPa ISO 178
Izod충격강도, +23°C 40 kJ/m² ISO 180/1U
아이조드 충격은 노치, +23°C 9.5 kJ/m² ISO 180/1A
쇼어 D 경도 86 - ISO 7619-1
열적 특성단위시험규격
ISO 데이터
녹는점, 10°C/min 343 °C ISO 11357-1/-3
유리 전이 온도, 10 °C/min 143 °C ISO 11357-1/-2
하중하에서의 변형온도, 1.80 MPa 325 °C ISO 75-1/-2
선형 열팽창 계수, 평행 8 E-6/K ISO 11359-1/-2
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 2 mm -
전기적 특성단위시험규격
ISO 데이터
부피 저항 100000 Ohm*m IEC 62631-3-1
기타 특성단위시험규격
물에서의 흡수성 0.35 % ISO 62와 유사
밀도 1370 kg/m³ ISO 1183
Processing Recommendation Injection Molding단위시험규격
Pre-drying - Temperature 120 - 150 °C -
Pre-drying - Time 3 - 5 h -
Processing humidity ≤0.02 % -
성형온도 180 - 210 °C -
Feed temperature ≤100 °C -
Zone 1 375 °C -
Zone 2 380 °C -
Zone 3 385 °C -
Zone 4 390 °C -
Nozzle temperature 395 °C -
특징
생산 공정
사출 성형, 기타 압출
인도 유형
펠렛 (입자,알갱이), 검정
특성
Tribologic Grade
내화학성에
General Chemical Resistance
Certifications
Food contact, Food approval FDA 21 CFR
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.