Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Novarex™ 7022E TW3 - PC - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for Novarex™ 7022E TW3:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Novarex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
투명한

ISO 1043 PC
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 23 cm³/10min ISO 1133
온도 300 °C -
하중 1.2 kg -
성형 수축률, 평행 0.6 % ISO 294-4, 2577
성형 수축률, 수직 0.6 % ISO 294-4, 2577
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 2700 MPa ISO 527
항복강도 64 MPa ISO 527
항복변형률 6.3 % ISO 527
파단시 평균신율 >50 % ISO 527
챠피 충격 강도 , +23°C N kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 7 kJ/m² ISO 179/1eA
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 114 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 126 °C ISO 75-1/-2
선형 열팽창 계수, 평행 65 E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 66 E-6/K ISO 11359-1/-2
전기적 특성값단위시험규격
ISO 데이터
상대 유전율, 100Hz 3.2 - IEC 62631-2-1
상대 유전뮬, 1MHz 3.2 - IEC 62631-2-1
소산 인자, 100Hz 17 E-4 IEC 62631-2-1
소산 인자, 1MHz 97 E-4 IEC 62631-2-1
부피 저항 >1E13 Ohm*m IEC 62631-3-1
표면 저항 3E14 Ohm IEC 62631-3-2
전기 압력 18 kV/mm IEC 60243-1
기타 특성값단위시험규격
밀도 1200 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 120 °C -
Pre-drying - Time 4 - 8 h -
Processing humidity ≤0.03 % -
성형온도 70 - 100 °C -
Zone 1 260 - 280 °C -
Zone 2 270 - 290 °C -
Zone 3 270 - 310 °C -
Nozzle temperature 270 - 310 °C -
특징
생산 공정
사출 성형
특별 특성
투명도
지역별 검색
쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧
기타 정보
사E성
Injection Molding Recommendations
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.