Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin NHP8000VT3 - (PPE+PS) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin NHP8000VT3:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
NORYL NHP8000VT3 resin is a non-reinforced blend of polyphenylene ether (PPE) + polystyrene (PS) designed for high heat resistance, ultra-thin-wall FR and High tracking resistance performance. This extrusion and injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries CTI 600V / PLC 0 and UL94 flame rating of V0 at 0.25mm. NORYL NHP8000VT3 is based on a unique co-polymer technology and exhibits high impact, high heat resistance, dimensional stability, hydrolytic stability, strong electrical performance, low moisture absorption and low specific gravity. This grade is targeted for electrical vehicle (EV) battery pack insulation sheet/film, bus bar insulation layer and other high voltage electric components.
UL Yellow Card E207780-104546521
Processing/Physical Characteristics값단위시험규격
ASTM 데이터
용융 흐름성, MFI 11.7 g/10min ASTM D 1238
온도 300 °C -
하중 5 kg -
성형 수축률, 평행 0.0073 mm/mm ASTM D 955
성형 수축률, 수직 0.0079 mm/mm ASTM D 955
기계적 특성값단위시험규격
ASTM 데이터
인장탄성률 2491 MPa ASTM D 638
항복강도 66.8 MPa ASTM D 638
항복변형률 4.2 % ASTM D 638
파단시 신율 10.8 % ASTM D 638
굴곡 계수 2600 MPa ASTM D 790
굴곡 강도 108 MPa ASTM D 790
아이조드 충격은 노치, 1/8 in 211 J/m ASTM D 256
아이조드 충격은 노치, Low-Temperature 84 J/m ASTM D 256
온도 -40 °C -
Izod충격강도, 1/8 in N J/m ASTM D 256
열적 특성값단위시험규격
ISO 데이터
두께 H인 제품의 난연성 V-0 class IEC 60695-11-10
테스트 두께 0.2 mm -
Yellow Card 유효한 예 - -
ASTM 데이터
DTUL @ 66 psi 150 °C ASTM D 648
DTUL @ 264 psi 133 °C ASTM D 648
비카트 연화 온도 155 °C ASTM D 1525
전기적 특성값단위시험규격
ISO 데이터
CTI 600 - IEC 60112
ASTM 데이터
표면 저항 7.5E16 Ohm ASTM D 257
부피 저항 6.2E15 Ohm*cm ASTM D 257
기타 특성값단위시험규격
밀도 1100 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 100 - 120 °C -
Pre-drying - Time 3 - 5 h -
용융수지온도 280 - 330 °C -
성형온도 70 - 120 °C -
Zone 1 280 - 330 °C -
Zone 2 280 - 330 °C -
Zone 3 280 - 330 °C -
Nozzle temperature 250 - 330 °C -
Screw speed 20 - 100 rpm -
Back pressure 3 - 8 MPa -
특징
생산 공정
사출 성형, 기타 압출, 열성형
특별 특성
난연성, Halogen-free, 고충격 또는 고충격 보강, 열안정성
특성
Low Warpage
내화학성에
Hydrolytically Stable
응용
자동차의, 전기 및 전자
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.