Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Delrin® RA300CPE NC010 - POM - DuPont Engineering Polymers

Check here, which other Delrin datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 도표

Any use of this information falls under the rules of our disclaimer.

제품 설명서

Common features of Delrin® acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance, as well as resistance to moisture, gasoline, lubricants, solvents, and many other neutral chemicals. Delrin® acetal resins also have excellent dimensional stability and good electrical insulating characteristics. They are naturally resilient, self-lubricating, and available in a variety of colors and speciality grades.

Delrin® acetal resin typically is used in demanding applications in the automotive, domestic appliances, sports, industrial engineering, electronics, and consumer goods industries.

Delrin® RA300CPE is a medium-high viscosity acetal homopolymer with outstanding balance of ease of processing and part performance, and with very low VOC emissions, reduced lifecycle greenhouse gas emissions and lower fossil resource use. Delrin® RA300CPE provides optimum mechanical performance with its excellent combination of toughness and strength with improved processing, thermal stability and productivity for injection molding.

Delrin® Renewable Attributed base polymer is produced from 100% bio-feedstock from waste*. 100% certified renewable electricity is used for its production.
This approach helps customers in achieving their sustainability goals.

* according to ISCC Plus mass balance certification.

Processing/Physical Characteristics	값	단위	시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR	6	cm³/10min	ISO 1133
온도	190	°C	-
하중	2.16	kg	-
성형 수축률, 평행	2.1	%	ISO 294-4, 2577
성형 수축률, 수직	1.8	%	ISO 294-4, 2577

기계적 특성	값	단위	시험규격
ISO 데이터
인장탄성률	3100	MPa	ISO 527
항복강도	71	MPa	ISO 527
항복변형률	25	%	ISO 527
파단시 평균신율	40	%	ISO 527
챠피 충격 강도 , +23°C	N	kJ/m²	ISO 179/1eU
챠피 충격 강도, -30°C	370	kJ/m²	ISO 179/1eU
챠피 노치드 충격 강도, +23°C	10.5	kJ/m²	ISO 179/1eA
챠피 노치드 충격 강도, -30°C	10	kJ/m²	ISO 179/1eA

열적 특성	값	단위	시험규격
ISO 데이터
녹는점, 10°C/min	178	°C	ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa	94	°C	ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa	165	°C	ISO 75-1/-2
선형 열팽창 계수, 평행	110	E-6/K	ISO 11359-1/-2
선형 열팽창 계수, 수직	110	E-6/K	ISO 11359-1/-2
1.5mm 평균두께에서의 난연성	HB	class	IEC 60695-11-10
테스트 두께	1.5	mm	-
Yellow Card 유효한	예	-	-
두께 H인 제품의 난연성	HB	class	IEC 60695-11-10
테스트 두께	0.8	mm	-
Yellow Card 유효한	예	-	-

전기적 특성	값	단위	시험규격
ISO 데이터
상대 유전율, 100Hz	3.8	-	IEC 62631-2-1
상대 유전뮬, 1MHz	3.5	-	IEC 62631-2-1
소산 인자, 1MHz	56	E-4	IEC 62631-2-1
부피 저항	>1E13	Ohm*m	IEC 62631-3-1
표면 저항	>1E15	Ohm	IEC 62631-3-2
CTI	600	-	IEC 60112

기타 특성	값	단위	시험규격
물에서의 흡수성	0.9	%	ISO 62와 유사
조건에서의 흡습성	0.2	%	ISO 62와 유사
밀도	1420	kg/m³	ISO 1183

도표

특징

생산 공정

사출 성형, 외형 압출, 시트 압출, 기타 압출

인도 유형

펠렛 (입자,알갱이), 자연 색상

부가물

이형제

특성

Low Emission, Thermal Stability, Homopolymer

Certifications

Contains renewable resources, ISCC Plus

지역별 검색

쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧

기타 정보

사E성

Drying is recommended, but not necessary for newly opened packaging stored in a dry location.

Follow the drying guidelines above in the following cases:

·         If moisture is above the Processing Moisture Content recommendation,

·         When a resin container is damaged,

·         When the material is not properly stored in a dry place at room temperature, or

·         When packaging stays open for a significant time.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.