Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Bakelite® UP 3415 - UP-(GF+X) - Bakelite Synthetics

Check here, which other Bakelite datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 테스트 견본 생산 - 도표

Any use of this information falls under the rules of our disclaimer.

제품 설명서

Product description:

Polyester moulding compound, inorganically filled, glass fibre reinforced, styrene free, very high dimensional stability, non flammable, high mechanical properties, UL listed moulding compound 0.75 mm / V-0 (ALL), RTI 170°C

Application areas:

Safety switch housings and electrotechnical parts, e. g. energy regulators, clamp boards, lamp parts, MCB housings, MCCB housings.

Property Name	Value	Unit	Standard No.
Apparent density (moulding compound)	0.9	g/cm³	ISO 60
Moulding shrinkage (injection moulding, longitudinal)	0.3	%	ISO 2577
Post shrinkage (injection moulding, 168h/110°C)	0.02	%	ISO 2577
Moulding shrinkage (compression moulding, longitudinal)	0.15	%	ISO 2577
Post shrinkage (compression moulding, 168h/110°C)	0.02	%	ISO 2577
Tensile strength (5mm/min)	45	MPa	ISO 527-1/2
Compr. strength (test spec. flat tested)	160	MPa	ISO 604
Flexural strength (2mm/min)	105	MPa	ISO 178
Flexural modulus	13000	MPa	ISO 178
Ball indentation hardness (H 961/30)	325	MPa	ISO 2039/P1
Water absorption (24h/23°C)	20	mg	similar to ISO 62

Additional characteristics:

high arc resistance

Preparation of Test Specimens of Thermosetting Moulding Compound

• Compression to ISO 295
• Injection to ISO 10724

Storage capability
12 month (shorter shelf life for darker colours), (relative humidity of 50-60% and maximum storage temperature of approximately 20°C)

Processing/Physical Characteristics	값	단위	시험규격
ISO 데이터
성형 수축률, 평행	0.3	%	ISO 294-4, 2577

기계적 특성	값	단위	시험규격
ISO 데이터
인장탄성률	10000	MPa	ISO 527
챠피 충격 강도 , +23°C	8.5	kJ/m²	ISO 179/1eU
챠피 노치드 충격 강도, +23°C	4.5	kJ/m²	ISO 179/1eA

열적 특성	값	단위	시험규격
ISO 데이터
하중하에서의 변형온도, 8.00 MPa	210	°C	ISO 75-1/-2
두께 H인 제품의 난연성	V-0	class	IEC 60695-11-10
테스트 두께	0.8	mm	-
Yellow Card 유효한	예	-	-

전기적 특성	값	단위	시험규격
ISO 데이터
상대 유전율, 100Hz	5.25	-	IEC 62631-2-1
소산 인자, 100Hz	0.02	E-4	IEC 62631-2-1
부피 저항	1E11	Ohm*m	IEC 62631-3-1
표면 저항	1E12	Ohm	IEC 62631-3-2
전기 압력	25	kV/mm	IEC 60243-1
CTI	600	-	IEC 60112

기타 특성	값	단위	시험규격
밀도	2000	kg/m³	ISO 1183

테스트 견본 생산	값	단위	시험규격
ISO 데이터
사출성형: 사출온도	105	°C	ISO 10724
사출성형: 사출속도	170	mm/s	ISO 10724
사출성형: 보압	100	MPa	ISO 10724
사출성형: 경화시간	25	min	ISO 10724
압축성형: 성형온도	160	°C	ISO 295
압축성형: 경화시간	1	min	ISO 295

도표

특징

생산 공정

사출 성형, 트랜스퍼 성형

지역별 검색

쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧

기타 정보

사E성

VERARBEITUNG

Temperature of material:	70 - 100	°C
Mould temperature:	160 - 180	°C
Curing time:	10-20	sec
Further Information:
Barrel temperature
- Feed zone:	60-70	°C
- Nozzle zone:	70-100	°C
Cavity moulding pressure:	>10	MPa
Back pressure:	0.5-1	MPa
Holding pressure:	60% of injection pressure

압E성

PROCESSING

Mould temperature:	160-180	°C
Curing time:	20-40	sec
Cavity moulding pressure:	>10	MPa

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.