Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Badalon® PC 30 - PC - Bada AG

Material Data Center offers the following functions for Badalon® PC 30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Badalon datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 36 cm³/10min ISO 1133
온도 300 °C -
하중 1.2 kg -
기계적 특성단위시험규격
ISO 데이터
인장탄성률 2300 MPa ISO 527
항복강도 60 MPa ISO 527
항복변형률 6 % ISO 527
파단시 강도 55 MPa ISO 527
파단시 신율 70 % ISO 527
굴곡 계수, 23°C 2300 MPa ISO 178
굴곡 강도 85 MPa ISO 178
챠피 충격 강도, +23°C N kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C N kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 55 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 10 kJ/m² ISO 179/1eA
Ball indentation hardness 125 MPa ISO 2039-1
열적 특성단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 121 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 133 °C ISO 75-1/-2
비카트 연화 온도, A 145 °C ISO 306
비카트 연화 온도, B 140 °C ISO 306
1.5mm 평균두께에서의 난연성 V-2 class IEC 60695-11-10
테스트 두께 1.6 mm -
두께 H인 제품의 난연성 V-2 class IEC 60695-11-10
테스트 두께 0.8 mm -
Glow Wire Flammability Index (GWFI) 850 °C IEC 60695-2-12
GWFI - thickness tested (1) 10 mm -
전기적 특성단위시험규격
ISO 데이터
상대 유전뮬, 1MHz 3.1 - IEC 62631-2-1
부피 저항 1E12 Ohm*m IEC 62631-3-1
표면 저항 1E15 Ohm IEC 62631-3-2
전기 압력 35 kV/mm IEC 60243-1
CTI 275 - IEC 60112
기타 특성단위시험규격
물에서의 흡수성 0.35 % ISO 62와 유사
조건에서의 흡습성 0.15 % ISO 62와 유사
밀도 1200 kg/m³ ISO 1183
Processing Recommendation Injection Molding단위시험규격
Pre-drying - Temperature 120 °C -
Pre-drying - Time 3 h -
Processing humidity ≤0.02 % -
용융수지온도 280 - 320 °C -
성형온도 80 - 120 °C -
특징
생산 공정
사출 성형
부가물
이형제
특별 특성
U.V. 안정성 또는 기후 안정성
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.