Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALFATER XL A65E 2GP0000 WT1159-17 - TPV - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALFATER XL A65E 2GP0000 WT1159-17:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Alfater datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
제품 설명서
Base PolymerThermoplastic Vulcanisate (PP+EPDM)
Colournatural color,white,black
Service Temperaturemax. range (depending on load, geometry, etc.) -40-125 °C
Special Featureshigh viscosity,good weathering resistance,good chemical resistance,good ozone reistance,good hot air resistance,good hydrolysis resistant
Market SegmentAutomotive,building and construction,Machinery,electrical and electronic,Furniture
Application Areaextruded parts,blow moulded parts,coextrusion
Typical Applicationsprofile,seals,sealing lip,conduit,tubes,cable guides,cable jacketing,bellows,air duct,2K components
Adhesion toPolypropylene Homopolymer,Polypropylene Copolymer,Polyethylene,Thermoplastic Vulcanisate (PP+EPDM),Thermoplastic Olefin Elastomer,Thermoplastic Elastomer general
기계적 특성단위시험규격
ISO 데이터
전단강도 28 kN/m ISO 34-1
쇼어 A 경도 65 - ISO 7619-1
열적 특성단위시험규격
ISO 데이터
1.5mm 평균두께에서의 난연성 HB class IEC 60695-11-10
테스트 두께 1.5 mm -
전기적 특성단위시험규격
ISO 데이터
CTI 600 - IEC 60112
기타 특성단위시험규격
밀도 930 kg/m³ ISO 1183
특징
생산 공정
사출 성형, Pipe/Tube Extrusion, 외형 압출, Wire/Cable Extrusion, 기타 압출, 중공 성형
인도 유형
검정, 자연 색상, 화이트
특별 특성
U.V. 안정성 또는 기후 안정성
내화학성에
General Chemical Resistance, Hydrolytically Stable, Ozone Resistance
응용
자동차의, 건물 건설, 전기 및 전자
지역별 검색
기타 정보
사E성
Pre-Drying Conditionsin a dry air (dessiccant) dryer 70-80 °C
for 2-4 h
max. moisture content <0,10 %
Processing Extrusionmelt temperature 190-230 °C
die temperature 190-210 °C
Storagedry, protected from light
not above 30°C
tightly sealed
기타 압출
Pre-Drying Conditions120 °C in a dry air (dessiccant) dryer
for 2-4 h
120 °C in an air circulating dryer
for 4-12 h
max. moisture content <0,01 %
Processing Extrusionextrusion melt temperature 240-280 °C
Storagedry, protected from light
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.