Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALCOM PBT 700/1.1 CF20 PTFE15 - (PBT+PTFE)-CF20 - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALCOM PBT 700/1.1 CF20 PTFE15:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Alcom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성
Any use of this information falls under the rules of our disclaimer.
제품 설명서
Base PolymerPolybutylene Terephthalate
Filler/Additive System20 % carbon fibres,15 % PTFE
Special Featureselectrically conductive,reduced surface resistivity,improved sliding / wear,heat stabilised
Market SegmentMachinery
Application Areainjection moulded parts
Typical Applicationshousings,functional components
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 16200 MPa ISO 527
파단시 강도 140 MPa ISO 527
파단시 신율 1.6 % ISO 527
챠피 충격 강도 , +23°C 37 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 6 kJ/m² ISO 179/1eA
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 217 °C ISO 75-1/-2
비카트 연화 온도, B 210 °C ISO 306
전기적 특성값단위시험규격
ISO 데이터
표면 저항 25 Ohm IEC 62631-3-2
기타 특성값단위시험규격
밀도 1470 kg/m³ ISO 1183
특징
생산 공정
사출 성형
특별 특성
증가된 전기전도성
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
기타 정보
사E성
Pre-Drying Conditionsin a dry air (dessiccant) dryer 100-120 °C
for 2-4 h
in an air circulating dryer 100-120 °C
for 4-8 h
dependant on moisture content
Processing Injection Mouldingmelt temperature 250-270 °C
mould temperature 80-120 °C
Storagedry, protected from light
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.