Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Terluran® SP-6 - ABS - INEOS Styrolution

Material Data Center offers the following functions for Terluran® SP-6:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Terluran datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성
Any use of this information falls under the rules of our disclaimer.
제품 설명서
High impact grade, suitable for extrusion.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 5.5 cm³/10min ISO 1133
온도 220 °C -
하중 10 kg -
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 1900 MPa ISO 527
항복강도 38 MPa ISO 527
항복변형률 2.8 % ISO 527
파단시 평균신율 9 % ISO 527
챠피 충격 강도 , +23°C N kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C 140 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 35 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 13 kJ/m² ISO 179/1eA
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 93 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 97 °C ISO 75-1/-2
비카트 연화 온도, B 90 °C ISO 306
선형 열팽창 계수, 평행 95 E-6/K ISO 11359-1/-2
1.5mm 평균두께에서의 난연성 HB class IEC 60695-11-10
테스트 두께 1.6 mm -
전기적 특성값단위시험규격
ISO 데이터
상대 유전율, 100Hz 2.9 - IEC 62631-2-1
상대 유전뮬, 1MHz 2.8 - IEC 62631-2-1
소산 인자, 100Hz 54 E-4 IEC 62631-2-1
소산 인자, 1MHz 82 E-4 IEC 62631-2-1
부피 저항 >1E13 Ohm*m IEC 62631-3-1
표면 저항 1E13 Ohm IEC 62631-3-2
CTI 600 - IEC 60112
기타 특성값단위시험규격
물에서의 흡수성 1.03 % ISO 62와 유사
조건에서의 흡습성 0.21 % ISO 62와 유사
밀도 1030 kg/m³ ISO 1183
특징
생산 공정
외형 압출, 시트 압출, 기타 압출
인도 유형
펠렛 (입자,알갱이)
지역별 검색
짱쨌쨈
기타 정보
기타 압출
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 2 - 4 h

PROCESSING
Extrusion, Pipes, Melt temperature: 200 - 230 °C
프로파일 압
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 2 - 4 h

PROCESSING
Extrusion, Profiles, Melt temperature: 210 - 240 °C
시트 압
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 2 - 4 h

PROCESSING
Extrusion, Plates, Melt temperature: 210 - 240 °C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.