Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin LTA6020 - Europe - (PPE+PS) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin LTA6020 - Europe:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
NORYL™ LTA6020 resin is a non-reinforced blend of polyphenylene ether (PPE) + high impact polystyrene (HIPS). This injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of 5VA at 2.5mm, 5VB at 2mm, and V0 at 1.5mm. NORYL LTA6020 exhibits good dimensional stability over a wide temperature range, high heat performance, low moisture uptake, and offers long-term aging / retention of mechanical properties. It is an excellent candidate for solar / photovoltaic (PV) junction boxes and outdoor electrical enclosures.

UL Yellow Card Link E45329-100960629
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 20 cm³/10min ISO 1133
온도 300 °C -
하중 5 kg -
ASTM 데이터
용융 흐름성, MFI 4 g/10min ASTM D 1238
온도 250 °C -
하중 10 kg -
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 2680 MPa ISO 527
항복강도 71 MPa ISO 527
항복변형률 4 % ISO 527
파단시 강도 57 MPa ISO 527
파단시 신율 8 % ISO 527
굴곡 계수 2600 MPa ISO 178
아이조드 노치 충격 강도, +23°C, 4mm 16 kJ/m² ISO 180/1A
아이조드 노치 충격 강도, -30°C, 4mm 8 kJ/m² ISO 180/1A
ASTM 데이터
항복강도 72 MPa ASTM D 638
항복변형률 6 % ASTM D 638
아이조드 충격은 노치, 1/8 in 220 J/m ASTM D 256
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 123 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 136 °C ISO 75-1/-2
비카트 연화 온도, 120°C/h 10N 155 °C ISO 306
비카트 연화 온도, 120°C/h 50N 144 °C ISO 306
1.5mm 평균두께에서의 난연성 V-0 class IEC 60695-11-10
테스트 두께 1.5 mm -
두께 H인 제품의 난연성 V-1 class IEC 60695-11-10
테스트 두께 1.0 mm -
두께가 h인 제품의 난연성 등급 5V 5VB class IEC 60695-11-20
테스트 두께 2.0 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (3) 1 mm -
Glow Wire Ignition Temperature (GWIT) 825 °C IEC 60695-2-13
GWIT - thickness tested (1) 1 mm -
Glow Wire Ignition Temperature (GWIT) 825 °C IEC 60695-2-13
GWIT - thickness tested (2) 2 mm -
Glow Wire Ignition Temperature (GWIT) 825 °C IEC 60695-2-13
GWIT - thickness tested (3) 3 mm -
기타 특성값단위시험규격
밀도 1130 kg/m³ ISO 1183
밀도 1130 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 105 °C -
Pre-drying - Time 3 - 4 h -
Processing humidity ≤0.02 % -
용융수지온도 280 - 300 °C -
성형온도 80 - 100 °C -
Feed temperature 60 - 80 °C -
Zone 1 260 - 280 °C -
Zone 2 280 - 300 °C -
Zone 3 270 - 290 °C -
특징
생산 공정
사출 성형
부가물
난연제
특별 특성
난연성
지역별 검색
짱쨌쨈
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.