Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin LPN170HG - (PPE+PS) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin LPN170HG:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 광학 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
NORYL LPN170HG resin is a non-reinforced blend of polyphenylene ether (PPE) + polystyrene (PS) designed for high heat resistance, low density, high gloss, low outgassing and good dimensional stability performance. This extrusion and injection moldable grade carries HDT 170°C, special gravity 1.07 g/cm3. This grade is capable for physical vapor deposition with good light distribution and high reflection rate. LPN170HG is targeted for automotive headlamp reflector, bezel, trim, light shielding and other high surface quality / high heat resistance demanded components.
Processing/Physical Characteristics값단위시험규격
ASTM 데이터
용융 흐름성, MFI 8.7 g/10min ASTM D 1238
온도 300 °C -
하중 5 kg -
성형 수축률, 평행 0.0083 mm/mm ASTM D 955
성형 수축률, 수직 0.0084 mm/mm ASTM D 955
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 2640 MPa ISO 527
항복강도 78 MPa ISO 527
항복변형률 5.3 % ISO 527
파단시 신율 15 % ISO 527
굴곡 계수, 23°C 2780 MPa ISO 178
굴곡 강도 125 MPa ISO 178
Izod충격강도, +23°C 71.9 kJ/m² ISO 180/1U
아이조드 충격은 노치, +23°C 4.3 kJ/m² ISO 180/1A
아이조드 충격은 노치 4.3 kJ/m² ISO 180/1A
온도 -40 °C -
ASTM 데이터
인장탄성률 2627 MPa ASTM D 638
항복강도 78 MPa ASTM D 638
항복변형률 5.2 % ASTM D 638
파단시 신율 31.2 % ASTM D 638
굴곡 계수 2655 MPa ASTM D 790
굴곡 강도 124 MPa ASTM D 790
아이조드 충격은 노치, 1/8 in 30 J/m ASTM D 256
아이조드 충격은 노치, Low-Temperature 35 J/m ASTM D 256
온도 -40 °C -
Izod충격강도, 1/8 in 791 J/m ASTM D 256
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 163 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 177 °C ISO 75-1/-2
선형 열팽창 계수, 평행 57.5 E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 59.3 E-6/K ISO 11359-1/-2
ASTM 데이터
DTUL @ 66 psi 180 °C ASTM D 648
DTUL @ 264 psi 170 °C ASTM D 648
전기적 특성값단위시험규격
ASTM 데이터
표면 저항 9.2E16 Ohm ASTM D 257
부피 저항 9.2E16 Ohm*cm ASTM D 257
광학 특성값단위시험규격
ASTM 데이터
광택도 101 - ASTM D 2457
기타 특성값단위시험규격
밀도 1070 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 100 - 120 °C -
Pre-drying - Time 3 - 5 h -
용융수지온도 300 - 340 °C -
성형온도 80 - 150 °C -
Zone 1 280 - 340 °C -
Zone 2 280 - 340 °C -
Zone 3 300 - 340 °C -
Nozzle temperature 300 - 340 °C -
Screw speed 20 - 100 rpm -
Back pressure 2 - 10 MPa -
특징
생산 공정
사출 성형, 기타 압출
특별 특성
열안정성
특성
High Gloss, Light Reflecting, Low Emission
응용
자동차의, 전기 및 전자
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.