Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin BN31 - Europe - (PPE+PS) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin BN31 - Europe:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
기계적 특성 - 열적 특성 - 기타 특성 - Processing Recommendation Injection Molding - Processing Recommendation Extrusion
Any use of this information falls under the rules of our disclaimer.
제품 설명서
NORYL™ BN31 resin is a non-reinforced blend of polyphenylene ether (PPE) + high impact polystyrene (HIPS). This blow moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of 5VA at 2.5mm and V0 at 1.5mm along with a UL746C Outdoor Suitability rating of F1. NORYL BN31 resin exhibit good low temperature impact strength, heat resistance, excellent processability, Low warpage, and dimensional stability. The material is an excellent candidate for blow molded applications such as hospital bed headboard, cladding, tray.

UL Yellow Card Link E121562-221152
기계적 특성값단위시험규격
ASTM 데이터
항복강도 48 MPa ASTM D 638
굴곡 계수 2410 MPa ASTM D 790
아이조드 충격은 노치, 1/8 in 267 J/m ASTM D 256
아이조드 충격은 노치, Low-Temperature 106 J/m ASTM D 256
온도 -40 °C -
열적 특성값단위시험규격
ISO 데이터
1.5mm 평균두께에서의 난연성 V-0 class IEC 60695-11-10
테스트 두께 1.5 mm -
두께가 h인 제품의 난연성 등급 5V 5VA class IEC 60695-11-20
테스트 두께 3.0 mm -
기타 특성값단위시험규격
밀도 1100 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 95 °C -
Processing Recommendation Extrusion값단위시험규격
Pre-drying - Temperature 95 °C -
Pre-drying - Time 2 - 4 h -
용융수지온도 210 - 215 °C -
성형온도 50 - 70 °C -
Zone 1 215 - 205 °C -
Zone 2 205 - 215 °C -
Zone 3 205 - 215 °C -
Zone 4 210 - 215 °C -
Zone 5 210 - 215 °C -
특징
생산 공정
중공 성형
부가물
난연제
특별 특성
난연성
지역별 검색
짱쨌쨈
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.