Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VECTRA® MT®4310 - LCP-GF30 - Celanese

Check here, which other Vectra datasheets, application examples or technical articles are available in Material Data Center

Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Funzioni

Any use of this information falls under the rules of our disclaimer.

Testo del prodotto

Vectra^® MT4310 VF3001 (natural) is a 30% glass reinforced high flow, LCP grade for injection molding.

Vectra^® MT4310 VF3001 (natural) is a special grade developed for medical industry applications and complies with:

• Food Contact Substance Notification (FCN) No. 742 of the Food and Drug Administration (FDA) and is listed in the Drug Master File (DMF 8464) and the Device Master File (MAF 315)
• the corresponding EU and national registry regulatory requirements
• biocompatibility in tests corresponding to USP 23 Class VI/ISO 10993
• low residual monomers
• no animal products

Highest temperature capability
Easiest flow
Suitable where very thin walls are required
Used for broad range of SMT applications, with minimal dimensional change
Chemical abbreviation according to ISO 1043-1 : LCP
Inherently flame retardant

Flammability at thickness h

V-0

-

Caratteristiche Fisiche	Valore	Unitá	Norma del test
ISO Data
Ritiro di stampaggio, parallelo	0.1	%	ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare	0.5	%	ISO 294-4, 2577

Proprietà Meccaniche	Valore	Unitá	Norma del test
ISO Data
Modulo a trazione	16000	MPa	ISO 527
Carico unitario a rottura	160	MPa	ISO 527
Deformazione a rottura	1.6	%	ISO 527
Resistenzia all'urto Charpy con intaglio, +23°C	40	kJ/m²	ISO 179/1eA

Proprietà Termiche	Valore	Unitá	Norma del test
ISO Data
Temperatura di fusione, 10°C/min	335	°C	ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa	276	°C	ISO 75-1/-2
Temp.di inflessione sotto caricor, 8.00 MPa	216	°C	ISO 75-1/-2
Temp.di rammollimento Vicat, B	195	°C	ISO 306
Coeff.di dilatazione termica lin., parallelo	7	E-6/K	ISO 11359-1/-2
Coeff.di dilatazione termica lin., perpend.	20	E-6/K	ISO 11359-1/-2
Reazione al fuoco a spessore h	V-0	class	IEC 60695-11-10
Indice di ossigeno	45	%	ISO 4589-1/-2

Proprietà Elettriche	Valore	Unitá	Norma del test
ISO Data
Costante dielettrica relativa, 100Hz	4	-	IEC 62631-2-1
Costante dielettrica relativa, 1MHz	3.3	-	IEC 62631-2-1
Fattore di dissipazione, 100Hz	100	E-4	IEC 62631-2-1
Fattore di dissipazione, 1MHz	250	E-4	IEC 62631-2-1
Resistività volumica	1E13	Ohm*m	IEC 62631-3-1
Resistività superficiale	1E14	Ohm	IEC 62631-3-2
Rigidità dielettrica	32	kV/mm	IEC 60243-1

Altre Proprietà	Valore	Unitá	Norma del test
Massa volumica	1610	kg/m³	ISO 1183

Funzioni

Caratteristiche

Processabilità e Forma di Forni

Stampaggio ad Iniezione

Forma fisica disponibile

Pellet, Colore naturale

Caratteristiche speciali

Ritardante di fiamma, Stabilizzato o stabile alla luce, Sterilizzabile, Sterilizzazione ad ossido di etilene (EtO), Sterilizzazione a vapore, Gamma irradiation sterilization

Certifications

Contatto con gli alimenti, Approvazione per contatto con gli alimenti BfR, Approvato per l'utilizzo per contatto con alimenti secondo la FDA 21 CFR, Food contact notification (FCN), Grado medico, Biocompatibility ISO 10993, Approvazione della USP class VI, Drug Master File, Device Master File

Applicazioni

Medicale

Disponibilità geografica

Nord America, Europa

Altre informazioni

Stampaggio ad Iniezione

Vectra resins are well known for their excellent thermal and hydrolytic stability. In order to ensure these properties are optimum, the resin should be dried correctly prior to processing. Vectra LCP MT4310 and MT4350 should be dried at 150°C for a minimum of 6 hours or at 170°C for a minimum of 4 hours in a desiccant dryer.
A three-zone screw evenly divided into feed, compression, and metering zones is preferred. A higher percentage of feed flights may be needed for smaller machines: 1/2 feed, 1/4 compression, 1/4 metering.

Vectra LCPs are shear thinning, their melt viscosity decreases quickly as shear rate increases. For parts that are difficult to fill, the molder can increase the injection velocity to improve melt flow.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.