Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Dynaflex™ G7940-9001-02 - TPE - Avient Corporation

Material Data Center offers the following functions for Dynaflex™ G7940-9001-02:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Dynaflex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ASTM Data
Indice di fluidità a caldo, MFI 2 g/10min ASTM D 1238
Temperatura 200 °C -
Carico 5 kg -
Ritiro di stampaggio, parallelo 0.017 mm/mm ASTM D 955
Proprietà MeccanicheValoreUnitáNorma del test
ASTM Data
Modulo a 100% allungamento 1.24 MPa ASTM D 412
Modulo a 300% allungamento 0.68 MPa ASTM D 412
Durezza A Shore 40 - ASTM D 2240
Resistenza alla lacerazione 17.5 kN/m ASTM D 624
Compressione residua, 22 hr @ 73 °F 12 % ASTM D 395
Resistenza alla trazione a rottura 3.59 MPa ASTM D 412
Allungamento a rottura 580 % ASTM D 412
Proprietà TermicheValoreUnitáNorma del test
ASTM Data
UL 94 combustibilitá HB - UL 94
Spessore testati 1.5 mm -
Altre ProprietàValoreUnitáNorma del test
Densità 1180 kg/m³ ASTM D 792
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Temperatura dello stampo 15.6 - 26.7 °C -
Zona 1 160 - 177 °C -
Zona 2 177 - 188 °C -
Zona 3 188 - 204 °C -
Temperatura dell ugello 188 - 204 °C -
Velocità di Rotazione della Vite 25 - 100 rpm -
Velocità di iniezione 25.4 - 127 mm/s -
Contropressione 0.345 - 1.03 MPa -
Pressione di chiusura 0.724 - 3.26 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet, Nero
Caratteristiche
Antisdrucciolo, Buona adesione, Soft Feel
Certifications
Contatto con gli alimenti, Approvato per l'utilizzo per contatto con alimenti secondo la FDA 21 CFR
Applicazioni
Polivalente, Attrezzature sportive
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.