Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FORTRON® 0214 - PPS - Celanese

Check here, which other Fortron datasheets, application examples or technical articles are available in Material Data Center

Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Funzioni

Any use of this information falls under the rules of our disclaimer.

Caratteristiche Fisiche	Valore	Unitá	Norma del test
ISO Data
Ritiro di stampaggio, parallelo	1.2	%	ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare	1.5	%	ISO 294-4, 2577
Densità del fuso	1150	kg/m³	-
Capacità termica specifica del fuso	1830	J/(kg K)	-

Proprietà Meccaniche	Valore	Unitá	Norma del test
ISO Data
Modulo a trazione	3800	MPa	ISO 527
Carico unitario a rottura	90	MPa	ISO 527
Deformazione a rottura	3	%	ISO 527

Proprietà Termiche	Valore	Unitá	Norma del test
ISO Data
Temperatura di fusione, 10°C/min	280	°C	ISO 11357-1/-3
Temperatura di transizione vetrosa, 10°C/min	90	°C	ISO 11357-1/-2
Temp.di inflessione sotto carico, 1.80 MPa	110	°C	ISO 75-1/-2
Temp.di inflessione sotto caricor, 8.00 MPa	95	°C	ISO 75-1/-2
Coeff.di dilatazione termica lin., parallelo	52	E-6/K	ISO 11359-1/-2
Coeff.di dilatazione termica lin., perpend.	53	E-6/K	ISO 11359-1/-2

Proprietà Elettriche	Valore	Unitá	Norma del test
ISO Data
Resistività volumica	1E9	Ohm*m	IEC 62631-3-1
Rigidità dielettrica	18	kV/mm	IEC 60243-1

Altre Proprietà	Valore	Unitá	Norma del test
Assorbimento d'acqua	0.02	%	Sim. alla ISO 62
Massa volumica	1350	kg/m³	ISO 1183

Funzioni

Caratteristiche

Processabilità e Forma di Forni

Stampaggio ad Iniezione, Estrusione Film, Estrusione di Lastre/Fogli, Altre Estrusioni

Forma fisica disponibile

Pellet, Polveri

Disponibilità geografica

Nord America, Europa, South and Central America, Near East/Africa

Altre informazioni

Stampaggio ad Iniezione

In spite of the minimum moisture absorption a drying of FORTRON is necessary. Predrying in a dehumidified air dryer at 120 degC/3-4 hours is recommended.
On injection molding machines with 15-25 D long three-section screws, are usual in the trade, the unreinforced FORTRON is processable. A shut-off nozzle is recommended.

Melt temperature 310-320 degC
Mold wall temperature at least 140 degC

A medium injection rate is normally preferred. All mold cavities must be effectively vented.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.