Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Celazole® TU‐60 - PBI - PBI Performance Products, Inc.

Material Data Center offers the following functions for Celazole® TU‐60:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Celazole datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Proprietà MeccanicheValoreUnitáNorma del test
ASTM Data
Modulo a trazione 5000 MPa ASTM D 638
Resistenza alla trazione 100 MPa ASTM D 638
Modulo alla compressione 2900 MPa ASTM D 695
Resistenza a compressione 206 MPa ASTM D 695
Modulo a flessione 5000 MPa ASTM D 790
Resistenza alla flessione 175 MPa ASTM D 790
Durezza Rockwell R 25 - ASTM D 785
Proprietà TermicheValoreUnitáNorma del test
ASTM Data
UL 94 combustibilitá V-0 - UL 94
Proprietà ElettricheValoreUnitáNorma del test
ASTM Data
Rigidità elettrica, breve periodo di tempo 17 kV/mm ASTM D 149
Resistenza di volume >1E15 Ohm*cm ASTM D 257
Resistenza all’arco 135 s ASTM D 495
Altre ProprietàValoreUnitáNorma del test
Assorbimento d’acqua, equilibrio 6.5 % ASTM D 570
Densità 1300 kg/m³ ASTM D 792
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 210 °C -
Pre-essiccamento - Tempo 6 h -
Temperatura di fusione 450 °C -
Temperatura dello stampo 200 °C -
Zona 1 380 °C -
Zona 2 420 °C -
Zona 3 430 °C -
Temperatura dell ugello 430 °C -
Pressione di Iniezione 200 - 250 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Caratteristiche speciali
Ritardante di fiamma, Stabilizzato o stabile al calore
Resistenza Chimica
Resistenza chimica generale
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.