Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Reny 1501AH - PAMXD6-GF30 - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for Reny 1501AH:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Reny datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquessec / condUnitéNorme du test
ISO Data
Indice de fluidité à chaud en volume, MVR 14 / * cm³/10min ISO 1133
Température 275 / * °C -
Charge 2.16 / * kg -
Indice de fluidité, MFI 20 g/10min ISO 1133
Température 275 °C -
Charge 2.16 kg -
Retrait au moulage, parallèle 0.3 / * % ISO 294-4, 2577
Retrait au moulage, perpendiculaire 0.6 / * % ISO 294-4, 2577
Propriétés mécaniquessec / condUnitéNorme du test
ISO Data
Module en traction 13300 / 11700 MPa ISO 527
Contrainte à la rupture 162 / 135 MPa ISO 527
Déformation à la rupture 1.6 / 1.6 % ISO 527
Module de flexion, 23°C 12100 / 11800 MPa ISO 178
Résistance à la flexion 251 / 222 MPa ISO 178
Résistance au choc Charpy, +23°C 37 / 29 kJ/m² ISO 179/1eU
Résistance au choc Charpy (entaillé), +23°C 5.3 / 5.5 kJ/m² ISO 179/1eA
Propriétés thermiquessec / condUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 1.80 MPa 220 / * °C ISO 75-1/-2
Température de fléchissement s/chrg, 0.45 MPa 237 / * °C ISO 75-1/-2
Coeffic. de dilatation therm. linéique, parallèle 20 / * E-6/K ISO 11359-1/-2
Coeffic. de dilatation therm. linéique, perpend. 50 / * E-6/K ISO 11359-1/-2
Inflammabilité ep. nom. 1.5 mm V-0 / * class IEC 60695-11-10
Epaisseur de l'éprouvette 1.6 / * mm -
Yellow Card disponible oui / * - -
Propriétés électriquessec / condUnitéNorme du test
ISO Data
Permittivité relative, 1MHz - / 4 - IEC 62631-2-1
Facteur de pertes, 1MHz - / 140 E-4 IEC 62631-2-1
Résistivité transversale 1E14 / 1E13 Ohm*m IEC 62631-3-1
Résistivité superficielle * / 4E14 Ohm IEC 62631-3-2
Rigidité diélectrique 29 / 26 kV/mm IEC 60243-1
Indice de résistance au cheminement 450 / 400 - IEC 60112
Propriétés diversessec / condUnitéNorme du test
Absorption d'humidité 1.2 / * % Sim. to ISO 62
Masse volumique 1560 / - kg/m³ ISO 1183
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 120 °C -
Pré-séchage - temps 3 h -
Température du moule 120 - 140 °C -
Zone 1 265 °C -
Zone 2 270 °C -
Zone 3 275 °C -
Température de la buse 275 °C -
Vitesse de rotation de vis 60 - 150 rpm -
Pressions d'injection 20 - 150 MPa -
Caractéristiques
Transformation
Moulage par injection
Propriétés spéciales
Ignifugé
Applications
Automobile, Électrotechnique et électrique, General Purpose
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.