Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LUVOCOM 70-9046 - (PK+PTFE) - LEHVOSS Group

Material Data Center offers the following functions for LUVOCOM 70-9046:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Luvocom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ISO Data
Indice de fluidité à chaud en volume, MVR 5 cm³/10min ISO 1133
Température 250 °C -
Charge 5 kg -
Retrait au moulage, parallèle 1.9 % ISO 294-4, 2577
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Module en traction 1400 MPa ISO 527
Résistance à la traction 50 MPa ISO 527
Module de flexion, 23°C 1200 MPa ISO 178
Résistance au choc Charpy (entaillé), +23°C 22 kJ/m² ISO 179/1eA
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 1.80 MPa 100 °C ISO 75-1/-2
Température de ramolliss. Vicat, A 200 °C ISO 306
Propriétés électriquesValeurUnitéNorme du test
ISO Data
Résistivité superficielle 1E12 Ohm IEC 62631-3-2
Propriétés diversesValeurUnitéNorme du test
Masse volumique 1330 kg/m³ ISO 1183
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 120 °C -
Pré-séchage - temps 1 - 4 h -
L'humidité de traitement ≤0.02 % -
Température de la matière fondue 245 °C -
Température du moule 60 - 100 °C -
Zone 1 230 - 250 °C -
Zone 2 230 - 260 °C -
Zone 3 240 - 260 °C -
Température de la buse 250 - 265 °C -
Caractéristiques
Transformation
Moulage par injection
Conditionnement
Couleurs naturelles
Additifs
Lubrifiant
Caractéristiques
Grade tribologique
Résistance Chimique
Résistance chimique générale
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.