Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Fiberfil® J-60/15/MI/20 - PP-(GF+P)35 - LyondellBasell Industries

Material Data Center offers the following functions for Fiberfil® J-60/15/MI/20:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Fiberfil datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés diverses - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ASTM Data
Retrait au moulage , parallèle 0.025 mm/mm ASTM D 955
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Contrainte d'écoulement 41 MPa ISO 527
Déformation au seuil d'écoulement 2.5 % ISO 527
Module de flexion, 23°C 5000 MPa ISO 178
Résistance à la flexion 60 MPa ISO 178
Résistance au choc Izod avec entaille, +23°C 3.2 kJ/m² ISO 180/1A
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 1.80 MPa 146 °C ISO 75-1/-2
Température de fléchissement s/chrg, 0.45 MPa 154 °C ISO 75-1/-2
Propriétés diversesValeurUnitéNorme du test
Absorption d’eau, 24hr 0.04 % ASTM D 570
Densité 1180 kg/m³ ASTM D 792
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 77 °C -
Pré-séchage - temps 2 h -
L'humidité de traitement ≤0.2 % -
Température de la matière fondue 199 - 232 °C -
Température du moule 32 - 71 °C -
Zone 1 199 - 210 °C -
Zone 2 204 - 227 °C -
Zone 3 182 - 199 °C -
Température de la buse 182 - 193 °C -
Contre-pression 0 - 0.689 MPa -
Caractéristiques
Transformation
Moulage par injection
Conditionnement
Granulés
Caractéristiques
Homopolymère
Disponibilité régionale
Amérique du nord
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.