Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Bakelite® UP 3630 - UP-X - Bakelite Synthetics

Check here, which other Bakelite datasheets, application examples or technical articles are available in Material Data Center

Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses - Préparation et conditionnement des éprouvettes - Fonctions

Any use of this information falls under the rules of our disclaimer.

Informations produit

Product description:

Polyester moulding compound, mainly organically filled, styrene free, processing shrinkage as for phenolic moulding compounds, high surface quality.

Application areas:

Domestic appliance sector and oven strips.

Property Name	Value	Unit	Standard No.
Apparent density (moulding compound)	0.68	g/cm³	ISO 60
Moulding shrinkage (compression moulding, longitudinal)	0.55	%	ISO 2577
Post shrinkage (compression moulding, 168h/110°C)	0.2	%	ISO 2577
Tensile strength (5mm/min)	50	MPa	ISO 527-1/2
Compr. strength (test spec. flat tested)	210	MPa	ISO 604
Flexural strength (2mm/min)	80	MPa	ISO 178
Flexural modulus	7500	MPa	ISO 178
Ball indentation hardness (H 961/30)	260	MPa	ISO 2039/P1
Water absorption (24h/23°C)	105	mg	similar to ISO 62

Preparation of Test Specimens of Thermosetting Moulding Compound

• Compression to ISO 295
• Injection to ISO 10724

Storage capability
12 month (shorter shelf life for darker colours), (relative humidity of 50-60% and maximum storage temperature of approximately 20°C)

Propriétés mécaniques	Valeur	Unité	Norme du test
ISO Data
Module en traction	8500	MPa	ISO 527
Résistance au choc Charpy, +23°C	7	kJ/m²	ISO 179/1eU
Résistance au choc Charpy (entaillé), +23°C	1.8	kJ/m²	ISO 179/1eA

Propriétés thermiques	Valeur	Unité	Norme du test
ISO Data
Température de fléchissement s/chrg, 8.00 MPa	80	°C	ISO 75-1/-2

Propriétés électriques	Valeur	Unité	Norme du test
ISO Data
Permittivité relative, 100Hz	5	-	IEC 62631-2-1
Facteur de pertes, 100Hz	0.02	E-4	IEC 62631-2-1
Résistivité transversale	1E10	Ohm*m	IEC 62631-3-1
Résistivité superficielle	1E11	Ohm	IEC 62631-3-2
Rigidité diélectrique	29	kV/mm	IEC 60243-1
Indice de résistance au cheminement	600	-	IEC 60112

Propriétés diverses	Valeur	Unité	Norme du test
Masse volumique	1740	kg/m³	ISO 1183

Préparation et conditionnement des éprouvettes	Valeur	Unité	Norme du test
ISO Data
Injection, temp. de la matière plastif.	105	°C	ISO 10724
Injection, vitesse d'injection	170	mm/s	ISO 10724
Injection, pression de maintien	100	MPa	ISO 10724
Injection, durée de recuit	25	min	ISO 10724
Compression, température du moule	160	°C	ISO 295
Compression, temps de recuit	1	min	ISO 295

Fonctions

Caractéristiques

Transformation

Moulage par injection, Moulage par transfert

Disponibilité régionale

Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique

Autres informations

Moulages par injection

VERARBEITUNG

Temperature of material:	100 - 110	°C
Mould temperature:	160 - 190	°C
Curing time:	10-20	sec
Further Information:
Barrel temperature
- Feed zone:	60-70	°C
- Nozzle zone:	70-100	°C
Cavity moulding pressure:	>10	MPa
Back pressure:	0.5-1	MPa
Holding pressure:	60% of injection pressure

Moulage par compression

PROCESSING

Mould temperature:	160-180	°C
Curing time:	20-40	sec
Cavity moulding pressure:	>10	MPa

Conditions générales

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.