Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ZYPEEK® 550G - PEEK - Jilin Joinature Polymer Co.,Ltd.

Material Data Center offers the following functions for ZYPEEK® 550G:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Zypeek datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Índice de fluidez, MFI 20 g/10min ISO 1133
Temperatura 380 °C -
Carga 5 kg -
Contracción posterior al moldeo, paralelo 1.0 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 1.3 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de fluencia 100 MPa ISO 527
Alargamiento a rotura 40 % ISO 527
Módulo de flexión, 23°C 4200 MPa ISO 178
Resistencia al impacto Charpy c/entalla, +23°C 6 kJ/m² ISO 179/1eA
Resistencia al impacto Izod con entalla, +23°C 6.5 kJ/m² ISO 180/1A
Dureza Shore D 85 - ISO 7619-1
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 343 °C ISO 11357-1/-3
Temp. de transición vítrea, 10°C/min 143 °C ISO 11357-1/-2
Estabilidad al calor, 1.80 MPa 152 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 45 E-6/K ISO 11359-1/-2
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Factor de pérdidas dieléctricas, 1MHz 30 E-4 IEC 62631-2-1
Resistividad volumétrica específica 1E14 Ohm*m IEC 62631-3-1
Resistencia dieléctrica 23 kV/mm IEC 60243-1
Indice comparativo de linea de fuga 150 - IEC 60112
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.4 % Sim. to ISO 62
Densidad 1300 kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección, Otros tipos de extrusión
Forma de suministro
Granulado
Características especiales
Resistencia mejorada al fuego, Alto impacto o modificado al impacto, Esterilizable, Esterilización por vapor, Gamma irradiation sterilization
Características
Grado tribológico
Certifications
Contacto con alimentos, Aprobado por el FDA 21 CFR
Applicaciones
Electrica, Médico
Disponibilidad regional
Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.