Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin AUT200AR - Europe - PEI - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin AUT200AR - Europe:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Texto del producto
High flow Polyetherimide (Tg 217°C) with low level of transparent mold release. Very low outgassing and plateout for optimally reduced need for mold cleaning. May be beneficial for automotive lighting applications where highly metallized, reflective surfaces are required. Haze onset temperature of 204°C (SABIC IP method).
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 25 cm³/10min ISO 1133
Temperatura 360 °C -
Carga 5 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 3200 MPa ISO 527
Esfuerzo de fluencia 105 MPa ISO 527
Alarg. en límite elástico 6 % ISO 527
Resistencia a la tracción 85 MPa ISO 527
Alargamiento a rotura 50 % ISO 527
Modulo de Flexión 3300 MPa ISO 178
Resistencia al impacto Charpy c/entalla, +23°C 3 kJ/m² ISO 179/1eA
Izod impact strength, +23°C, 4mm N kJ/m² ISO 180/1U
Izod impact strength, -30°C, 4mm N kJ/m² ISO 180/1U
Res. impacto Izod c/entalla, +23°C, 4mm 5 kJ/m² ISO 180/1A
Res. impacto Izod c/entalla, -30°C, 4mm 5 kJ/m² ISO 180/1A
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 193 °C ISO 75-1/-2
Temp. reblandecimiento Vicat, A 215 °C ISO 306
Temp. reblandecimiento Vicat, B 211 °C ISO 306
Temp. reblandecimiento Vicat, 120°C/h 50N 212 °C ISO 306
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 1.25 % Sim. to ISO 62
Absorción de humedad 0.7 % Sim. to ISO 62
Densidad 1270 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 150 °C -
Tiempo de pre-secado 4 - 6 h -
Humedad de procesamiento ≤0.02 % -
Temperatura de la masa 350 - 400 °C -
Temperatura del molde 135 - 165 °C -
Zona 1 330 - 400 °C -
Zona 2 340 - 400 °C -
Zona 3 345 - 400 °C -
Velocidad de giro de husillo 40 - 70 rpm -
Contrapresión 0.3 - 0.7 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Transparente
Applicaciones
Automotriz
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.