Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin 1285 - Americas - PEI - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin 1285 - Americas:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Texto del producto
Transparent Polyetherimide blend. ECO Conforming. US FDA and EU Food Contact Compliant in recognized colors.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ASTM Data
Índice de fluidez, MFI 8.1 g/10min ASTM D 1238
Temperatura 295 °C -
Carga 6.6 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ASTM Data
Módulo de tracción 3370 MPa ASTM D 638
Esfuerzo de fluencia a tracción 110 MPa ASTM D 638
Esfuerzo de fractura a tracción 82 MPa ASTM D 638
Alargamiento a la rotura 60 % ASTM D 638
Resistencia al impacto Izod con entalla, 1/8 in 26 J/m ASTM D 256
Propiedades térmicasValorUnidadesMétodo de ensayo
ASTM Data
Temperatura Vicat 181 °C ASTM D 1525
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1290 kg/m³ ASTM D 792
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 120 - 150 °C -
Tiempo de pre-secado 4 - 8 h -
Humedad de procesamiento ≤0.02 % -
Temperatura de la masa 300 - 330 °C -
Temperatura del molde 95 - 150 °C -
Zona 1 280 - 315 °C -
Zona 2 290 - 320 °C -
Zona 3 295 - 325 °C -
Velocidad de giro de husillo 50 - 100 rpm -
Contrapresión 0.7 - 1.4 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Transparente
Certifications
Contacto con alimentos, Aprobado por el FDA 21 CFR
Disponibilidad regional
Norteamérica
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.