Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox. Information about Biopolymers, a project by FH Hannover and M-Base Engineering & Software GmbH sponsored by Fachagentur Nachwachsende Rohstoffe (FNR).

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Tenite™ Propionate 360E4861316 - CAP - Eastman Chemical Co.

Material Data Center offers the following functions for Tenite™ Propionate 360E4861316:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Tenite datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Propiedades opticas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Texto del producto

Tenite™ cellulosic plastics are noted for their excellent balance of properties - toughness, hardness, strength, surface gloss, clarity, and a warm feel. The mechanical properties of Tenite™ cellulosic plastics differ with plasticizer levels. Lower plasticizer content yields a harder surface, higher heat resistance, greater rigidity, higher tensile strength, and better dimensional stability. Higher plasticizer content increases impact strength. Tenite™ cellulosic plastics are available in natural, clear, selected ambers or smoke transparents and black translucent.

Color concentrates are available in let-down ratios from 10:1 to 40:1.

Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ASTM Data
Contracción posterior al moldeo, paralelo 0.004 mm/mm ASTM D 955
Propiedades mecánicasValorUnidadesMétodo de ensayo
ASTM Data
Esfuerzo de fluencia a tracción 26.9 MPa ASTM D 638
Esfuerzo de fractura a tracción 30.3 MPa ASTM D 638
Alargamiento a la rotura 45 % ASTM D 638
Módulo de flexión 1241 MPa ASTM D 790
Dureza Rockwell 68 - ASTM D 785
Resistencia al impacto Izod con entalla, 1/8 in 533 J/m ASTM D 256
Resistencia al impacto Izod con entalla, baja temperatura 123 J/m ASTM D 256
Temperatura -40 °C -
Propiedades térmicasValorUnidadesMétodo de ensayo
ASTM Data
Coeficiente de dilatación térmica, long. 140 E-6/K ASTM D 696
Estabilidad al calor @ 66 psi 80 °C ASTM D 648
Estabilidad al calor @ 264 psi 72 °C ASTM D 648
Temperatura Vicat 92 °C ASTM D 1525
Conductividad térmica, estado sólido 0.036 W/(m K) ASTM C 177
Propiedades eléctricasValorUnidadesMétodo de ensayo
ASTM Data
Resistencia dieléctrica, tiempo corto 15.3 kV/mm ASTM D 149
Factor de pérdidas dieléctricas, 1 MHz 0.08 - ASTM D 150
Constante dieléctrica, 1 MHz 3.55 - ASTM D 150
Resistividad volumétrica 1E15 Ohm*cm ASTM D 257
Propiedades opticasValorUnidadesMétodo de ensayo
ASTM Data
Opacidad 8.5 % ASTM D 1003
Índice de refracción 1.48 - ASTM D 542
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua, 24hr 1.4 % ASTM D 570
Densidad 1190 kg/m³ ASTM D 792
Características
Procesamiento y forma de entrega
Extrusión de perfiles
Aditivos
Plastificante
Características especiales
Transparente
Características
High Gloss
Certifications
Contiene recursos renovables, Contacto con alimentos, Aprobado por el FDA 21 CFR
Applicaciones
Empacado
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.