Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of TECACOMP® PEEK LDS black 1047045 - PEEK-MX - Ensinger Compounds

Material Data Center offers the following functions for TECACOMP® PEEK LDS black 1047045:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Tecacomp datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Índice de fluidez, MFI 77 g/10min ISO 1133
Temperatura 380 °C -
Carga 10 kg -
Contracción posterior al moldeo, paralelo 0.5 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.6 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 10900 MPa ISO 527
Esfuerzo de tracción 105 MPa ISO 527
Alargamiento a rotura 2.5 % ISO 527
Resistencia al impacto Charpy, +23°C 35 kJ/m² ISO 179/1eU
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 343 °C ISO 11357-1/-3
Temp. de transición vítrea, 10°C/min 143 °C ISO 11357-1/-2
Estabilidad al calor, 1.80 MPa 218 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 18 E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 26 E-6/K ISO 11359-1/-2
Combustibilidad a espesor h V-0 class IEC 60695-11-10
Espesores de probeta 0.8 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Resistencia dieléctrica 17.5 kV/mm IEC 60243-1
Indice comparativo de linea de fuga 225 - IEC 60112
Other Standards[S]
Resistividad volumétrica específica 5.8E11 Ohm*m IEC 61340-2-3
Resistividad superficial específica 5.8E12 Ohm IEC 61340-2-3
S: These properties are reported by the producer according standards that are different to our defaults.
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de humedad 0.1 % Sim. to ISO 62
Densidad 1670 kg/m³ ISO 1183
Bulk density 900 kg/m³ -
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 150 °C -
Tiempo de pre-secado 4 h -
Humedad de procesamiento ≤0.02 % -
Temperatura de la masa 390 - 400 °C -
Temperatura del molde 160 - 210 °C -
Zona 1 360 - 400 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola, Negro
Características
Imprimible por láser
Applicaciones
Electrica, Médico
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.