Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Reny 4011 - PAMXD6-GF40 - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for Reny 4011:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Reny datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 4.5 / * cm³/10min ISO 1133
Temperatura 275 / * °C -
Carga 2.16 / * kg -
Índice de fluidez, MFI 6.3 g/10min ISO 1133
Temperatura 275 °C -
Carga 2.16 kg -
Contracción posterior al moldeo, paralelo 0.3 / * % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.6 / * % ISO 294-4, 2577
Propiedades mecánicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 21600 / 18600 MPa ISO 527
Resistencia a la tracción 152 / 143 MPa ISO 527
Alargamiento a rotura 1 / 1.1 % ISO 527
Módulo de flexión, 23°C 19800 / 19100 MPa ISO 178
Resistencia a la flexión 235 / 228 MPa ISO 178
Resistencia al impacto Charpy, +23°C 16 / 16 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 7.3 / 7.5 kJ/m² ISO 179/1eA
Propiedades térmicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 226 / * °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 235 / * °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 10 / * E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 40 / * E-6/K ISO 11359-1/-2
Combustibilidad a 1.5mm esp. nom. HB / * class IEC 60695-11-10
Espesores de probeta 1.6 / * mm -
Yellow Card disponible sí / * - -
Propiedades eléctricasSeco / CondUnidadesMétodo de ensayo
ISO Data
Resistividad volumétrica específica 300 / 6E8 Ohm*m IEC 62631-3-1
Resistividad superficial específica * / 3E6 Ohm IEC 62631-3-2
Otras propiedadesSeco / CondUnidadesMétodo de ensayo
Absorción de humedad 0.9 / * % Sim. to ISO 62
Densidad 1660 / - kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 120 °C -
Tiempo de pre-secado 3 h -
Temperatura del molde 120 - 140 °C -
Zona 1 265 °C -
Zona 2 270 °C -
Zona 3 275 °C -
Temperatura de boquilla 275 °C -
Velocidad de giro de husillo 60 - 150 rpm -
Presión de inyección 20 - 150 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Conductividad eléctrica aumentada
Applicaciones
Automotriz, Electrica, Uso general
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.