Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of POLYFORT® FPP 30 GFC - PP-GF30 - LyondellBasell Industries

Material Data Center offers the following functions for POLYFORT® FPP 30 GFC:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, parameters for material models, CAE Interfaces

Check here, which other Polyfort datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Texto del producto
30% chemical coupled glass fibre reinforced PP-homopolymer

Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 5 cm³/10min ISO 1133
Temperatura 230 °C -
Carga 2.16 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 6500 MPa ISO 527
Resistencia a la tracción 84 MPa ISO 527
Alargamiento a rotura 2.8 % ISO 527
Resistencia al impacto Charpy, +23°C 48 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy, -30°C 45 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 9 kJ/m² ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C 8 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 145 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 159 °C ISO 75-1/-2
Combustibilidad a 1.5mm esp. nom. HB class IEC 60695-11-10
Espesores de probeta 1.5 mm -
Yellow Card disponible - -
Combustibilidad a espesor h HB class IEC 60695-11-10
Espesores de probeta 3.0 mm -
Yellow Card disponible - -
Ratio de combustión, FMVSS, Espesor de 1mm 50 mm/min ISO 3795 (FMVSS 302)
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Resistividad volumétrica específica >1E13 Ohm*m IEC 62631-3-1
Resistividad superficial específica >1E15 Ohm IEC 62631-3-2
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1110 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 80 °C -
Tiempo de pre-secado 2 - 4 h -
Temperatura de la masa 230 - 270 °C -
Temperatura del molde 40 - 70 °C -
Funciones
Viscosidad-velocidad de cizallamiento , POLYFORT® FPP 30 GFC, PP-GF30, LyondellBasell
Tensión de cizalla-velocidad de cizalla , POLYFORT® FPP 30 GFC, PP-GF30, LyondellBasell
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Granulado
Aditivos
Desmoldeante
Disponibilidad regional
Demás información
Moldeo por inyección
PREPROCESSING; Pretreatment
Predrying usually not neccessary (2-4h / 80°C)

PROCESSING ;Processing:

Melttemperature230 - 270°C
Mouldtemperature40 - 70°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.