Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin ZM3640 - Asia - (PPE+PS)-MF - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin ZM3640 - Asia:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Texto del producto
NORYL™ ZM3640 resin is a mineral reinforced blend of polyphenylene ether (PPE) + high impact polystyrene (HIPS). This grade contains non-brominated, non-chlorinated flame retardant and has a UL94 flame rating of V1 at 1.5mm. NORYL ZM3640 resin exhibits high heat resistance, low warpage, good dimensional stability and is an excellent candidate for printer chassis applications.

UL Yellow Card Link E207780-100140832
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ASTM Data
Índice de fluidez, MFI 24 g/10min ASTM D 1238
Temperatura 300 °C -
Carga 2.16 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ASTM Data
Esfuerzo de fluencia a tracción 60 MPa ASTM D 638
Alargamiento a la rotura 4 % ASTM D 638
Resistencia al impacto Izod con entalla, 1/8 in 35 J/m ASTM D 256
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Combustibilidad a 1.5mm esp. nom. V-1 class IEC 60695-11-10
Espesores de probeta 1.5 mm -
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1220 kg/m³ ASTM D 792
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 90 - 95 °C -
Tiempo de pre-secado 3 - 4 h -
Humedad de procesamiento ≤0.02 % -
Temperatura de la masa 255 - 280 °C -
Temperatura del molde 65 - 90 °C -
Zona 1 220 - 270 °C -
Zona 2 230 - 275 °C -
Zona 3 245 - 280 °C -
Velocidad de giro de husillo 20 - 100 rpm -
Contrapresión 0.3 - 0.7 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Aditivos
Ignifugante
Características especiales
Resistencia mejorada al fuego
Disponibilidad regional
Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.