Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LUMICENE® mPE M 6040 - (PE-HD) - TotalEnergies

Material Data Center offers the following functions for LUMICENE® mPE M 6040:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Lumicene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades térmicas - Propiedades opticas - Otras propiedades - Propiedades mecánicas (Film) - Recomendación para procesamiento Extrusión
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Índice de fluidez, MFI 4 g/10min ISO 1133
Temperatura 190 °C -
Carga 2.16 kg -
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 134 °C ISO 11357-1/-3
Propiedades opticasValorUnidadesMétodo de ensayo
ISO Data
Niebla 12 - ISO 14782
ASTM Data
Brillo 51 - ASTM D 2457
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 960 kg/m³ ISO 1183
Propiedades mecánicas (Film)ValorUnidadesMétodo de ensayo
ISO Data
Tensión a fluencia, paralelo 23 MPa ISO 527-3
Tensión a fluencia, normal 24 MPa ISO 527-3
Resistencia a la tracción, paralelo 26 MPa ISO 527-3
Resistencia a la tracción, normal 34 MPa ISO 527-3
Alargamiento máximo, paralelo 520 % ISO 527-3
Alargamiento máximo, normal 850 % ISO 527-3
Caida de dardo A 40 g ISO 7765-1
Tipo de extrusión colada - -
Espesor de la muestra 0.02 mm -
Recomendación para procesamiento ExtrusiónValorUnidadesMétodo de ensayo
Temperatura de la masa 220 - 280 °C -
Temperatura del molde 20 - 80 °C -
Características
Procesamiento y forma de entrega
Extrusion del film
Características especiales
Estable contra el calor
Características
Propiedades de barrera, Resina de mezcla, Buen estiramiento, Low Neck-In
Resistencia quimica
Resistencia a la oxidación
Certifications
Contacto con alimentos
Applicaciones
Empacado
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.