Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LOXILLOY PC/ABS 1120-18 05022 - (PC+ABS) - Loxim Industries Limited

Material Data Center offers the following functions for LOXILLOY PC/ABS 1120-18 05022:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Loxilloy datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Índice de fluidez, MFI 20 g/10min ISO 1133
Temperatura 260 °C -
Carga 5 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de fluencia 52 MPa ISO 527
Alargamiento a rotura 50 % ISO 527
Módulo de flexión, 23°C 2300 MPa ISO 178
Resistencia a la flexión 78 MPa ISO 178
Resistencia al impacto Izod con entalla, +23°C 49 kJ/m² ISO 180/1A
Resistencia al impacto Izod con entalla 43 kJ/m² ISO 180/1A
Temperatura -30 °C -
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 100 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 122 °C ISO 75-1/-2
Temp. reblandecimiento Vicat, B 120 °C ISO 306
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1130 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 100 - 110 °C -
Tiempo de pre-secado 3 - 4 h -
Humedad de procesamiento ≤0.1 % -
Temperatura de la masa 275 - 300 °C -
Temperatura del molde 60 - 90 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Alto impacto o modificado al impacto, Estable contra el calor
Características
Ductil
Resistencia quimica
Resistencia química general
Applicaciones
Automotriz
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.