Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LOXIAMID PA6/ABS HS1 09002 - (PA6+ABS) - Loxim Industries Limited

Material Data Center offers the following functions for LOXIAMID PA6/ABS HS1 09002:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Loxiamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Índice de fluidez, MFI 30 g/10min ISO 1133
Temperatura 240 °C -
Carga 10 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de fluencia 40 MPa ISO 527
Alargamiento a rotura 10 % ISO 527
Módulo de flexión, 23°C 1600 MPa ISO 178
Resistencia a la flexión 65 MPa ISO 178
Resistencia al impacto Izod con entalla, +23°C 65 kJ/m² ISO 180/1A
Resistencia al impacto Izod con entalla 11 kJ/m² ISO 180/1A
Temperatura -40 °C -
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 62 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 90 °C ISO 75-1/-2
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1060 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 80 °C -
Tiempo de pre-secado 2 - 4 h -
Humedad de procesamiento ≤0.2 % -
Temperatura del molde 70 - 100 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Estable contra el calor
Características
Ductil
Resistencia quimica
Resistencia química general
Applicaciones
Automotriz
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.