Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FORTRON® 0320 - PPS - Celanese

Material Data Center offers the following functions for FORTRON® 0320:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Fortron datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Texto del producto
0320 exhibits a high melt strength for extrusion processes. The material demonstrates excellent heat and chemical resistance. The intended use of this product is for extruding monofilament/fibers, rod and slab. Available standard in powder 'flake' (0320B0), ground powder (0320B0/100 µm), pellet (0320P0) and crystallized pellet (0320C0) form.

Flammability at thickness h (3 mm)V-0-
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 1.2 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 1.5 % ISO 294-4, 2577
Calor especifico de la masa 1830 J/(kg K) -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 3500 MPa ISO 527
Resistencia a la tracción 90 MPa ISO 527
Alargamiento a rotura 8 % ISO 527
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 280 °C ISO 11357-1/-3
Temp. de transición vítrea, 10°C/min 90 °C ISO 11357-1/-2
Estabilidad al calor, 1.80 MPa 115 °C ISO 75-1/-2
Estabilidad al calor, 8.00 MPa 95 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 52 E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 53 E-6/K ISO 11359-1/-2
Combustibilidad a espesor h V-0 class IEC 60695-11-10
Espesores de probeta 3.0 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 1MHz 4.6 - IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz 11 E-4 IEC 62631-2-1
Resistividad volumétrica específica 1E9 Ohm*m IEC 62631-3-1
Resistencia dieléctrica 18 kV/mm IEC 60243-1
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.02 % Sim. to ISO 62
Densidad 1350 kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección, Extrusión de fibra, Extrusion del film, Extrusión de perfiles, Extrusión de láminas, Otros tipos de extrusión
Forma de suministro
Sémola, Polvo
Características especiales
Estable contra el calor
Características
Resistencia del fundido
Resistencia quimica
Resistencia química general
Applicaciones
Monofilamento
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric
Demás información
Moldeo por inyección
In spite of the minimum moisture absorption a drying of FORTRON is necessary. Predrying in a dehumidified air dryer at 120 degC/3-4 hours is recommended.
On injection molding machines with 15-25 D long three-section screws, are usual in the trade, the unreinforced FORTRON is processable. A shut-off nozzle is recommended.

Melt temperature 310-320 degC
Mold wall temperature at least 140 degC

A medium injection rate is normally preferred. All mold cavities must be effectively vented.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.