Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of EMERGE™ PC 8702-15 (AP) - PC-GX20 - Trinseo

Material Data Center offers the following functions for EMERGE™ PC 8702-15 (AP):
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Emerge datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ASTM Data
Índice de fluidez, MFI 15 g/10min ASTM D 1238
Temperatura 300 °C -
Carga 1.2 kg -
Contracción posterior al moldeo, paralelo 0.003 mm/mm ASTM D 955
Propiedades mecánicasValorUnidadesMétodo de ensayo
ASTM Data
Módulo de tracción 3999 MPa ASTM D 638
Esfuerzo de fractura a tracción 100 MPa ASTM D 638
Alargamiento a la rotura 4 % ASTM D 638
Resistencia al impacto Izod con entalla, 1/8 in 112 J/m ASTM D 256
Propiedades térmicasValorUnidadesMétodo de ensayo
ASTM Data
Combustibilidad UL 94 V-0 - UL 94
Espesores de probeta 1.5 mm -
Estabilidad al calor @ 66 psi 145 °C ASTM D 648
Estabilidad al calor @ 264 psi 140 °C ASTM D 648
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Indice comparativo de linea de fuga 175 - IEC 60112
ASTM Data
Resistencia dieléctrica, tiempo corto 27.2 kV/mm ASTM D 149
Constante dieléctrica, 1 MHz 3.1 - ASTM D 150
Resistividad superficial 3E14 Ohm ASTM D 257
Resistividad volumétrica >1E15 Ohm*cm ASTM D 257
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1330 kg/m³ ASTM D 792
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 121 °C -
Tiempo de pre-secado 3 - 4 h -
Temperatura de la masa 288 - 316 °C -
Temperatura del molde 79.4 - 116 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Aditivos
Desmoldeante
Características especiales
Resistencia mejorada al fuego, Sin fósforo
Applicaciones
IT / Equipo de oficina, Electrica
Disponibilidad regional
Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.