Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of DURANEX® 457EV - (PBT+PC) - Polyplastics

Material Data Center offers the following functions for DURANEX® 457EV:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Duranex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de tracción 46 MPa ISO 527
Alarg. nominal a rotura 13 % ISO 527
Módulo de flexión, 23°C 1970 MPa ISO 178
Resistencia a la flexión 73 MPa ISO 178
Resistencia al impacto Charpy c/entalla, +23°C 21 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 75 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 90 E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 100 E-6/K ISO 11359-1/-2
Combustibilidad a 1.5mm esp. nom. V-0 class IEC 60695-11-10
Espesores de probeta 1.5 mm -
Yellow Card disponible - -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Resistividad volumétrica específica 5E12 Ohm*m IEC 62631-3-1
Resistencia dieléctrica 20 kV/mm IEC 60243-1
Indice comparativo de linea de fuga 600 - IEC 60112
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1370 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura del molde 65 °C -
Zona 1 240 °C -
Zona 2 260 °C -
Zona 3 260 °C -
Velocidad de inyección 70 mm/s -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Aditivos
Ignifugante
Características especiales
Resistencia mejorada al fuego, Alto impacto o modificado al impacto, Estable contra rayos U.V./interperie, Estable contra el calor
Resistencia quimica
Resistencia al esfuerzo producido por condiciones ambientales
Applicaciones
Automotriz, Electrica
Disponibilidad regional
Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.