Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALTECH PC ECO 2015/509 GF15 - PC-GF15 - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALTECH PC ECO 2015/509 GF15:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Altech datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Texto del producto
Base PolymerPolycarbonate
Filler/Additive System15 % glass fibres
Special Featureseasy release (demoulding)
Market Segmentelectrical and electronic,building and construction
Application Areadomestic appliances,electrical components
Typical Applicationsvarious
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 4.5 cm³/10min ISO 1133
Temperatura 300 °C -
Carga 1.2 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 5400 MPa ISO 527
Resistencia a la tracción 90 MPa ISO 527
Alargamiento a rotura 3.5 % ISO 527
Resistencia al impacto Charpy, +23°C 40 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 9 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temp. reblandecimiento Vicat, B 141 °C ISO 306
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1300 kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección
Certifications
Contenido de resina reciclada
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, Próximo Oriente/Africa
Demás información
Moldeo por inyección
Pre-Drying Conditionsin a dry air (dessiccant) dryer 100-120 °C
for 2-3 h
in an air circulating dryer 100-120 °C
for 2-12 h
dependant on moisture content
max. moisture content <0,02 %
Processing Injection Mouldingmelt temperature 280-300 °C
mould temperature 80-100 °C
Storagedry, protected from light
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.