Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of THERMOLAST® K TC8GPZ - TPE - KRAIBURG TPE GmbH & Co. KG

Material Data Center offers the following functions for THERMOLAST® K TC8GPZ:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Thermolast datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de tracción 11 MPa ISO 37
Alargamiento a rotura 700 % ISO 37
Deformación permanente por compresión a 70°C, 24h 52 % ISO 815
Deformación permanente por compresión a 100°C, 24h 77 % ISO 815
Resistencia al desgarro 26 kN/m ISO 34-1
Dureza Shore A 79 - ISO 7619-1
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Combustibilidad a espesor h HB class IEC 60695-11-10
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1100 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 60 - 80 °C -
Tiempo de pre-secado 2 - 4 h -
Temperatura de la masa 200 - 250 °C -
Temperatura del molde 25 - 40 °C -
Zona 1 180 - 200 °C -
Zona 2 200 - 220 °C -
Zona 3 220 - 250 °C -
Presión de inyección 20 - 100 MPa -
Contrapresión 2 - 10 MPa -
Presión de mantenimiento 8 - 60 MPa -
Tiempo de residencia máxima 10 min -
Características
Procesamiento y forma de entrega
Moldeo por inyección, Otros tipos de extrusión
Forma de suministro
Negro
Características
Buenas propiedades de adhesión, Low Emission, Bajo empañamiento, Bajo olor, Textura suave
Applicaciones
Automotriz
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.