Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox. Information about Biopolymers, a project by FH Hannover and M-Base Engineering & Software GmbH sponsored by Fachagentur Nachwachsende Rohstoffe (FNR).

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Biomer® P226 - PHB - Biomer

Material Data Center offers the following functions for Biomer® P226:
unit conversion, PDF datasheet print, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Biomer datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 9.5 cm³/10min ISO 1133
Temperatura 180 °C -
Carga 5 kg -
Índice de fluidez, MFI 10 g/10min ISO 1133
Temperatura 180 °C -
Carga 5 kg -
Contracción posterior al moldeo, paralelo 1.2 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 1520 MPa ISO 527
Esfuerzo de tracción 25.5 MPa ISO 527
Resistencia al impacto Charpy, +23°C N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy, -30°C 30 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 2.7 kJ/m² ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C 1.4 kJ/m² ISO 179/1eA
Dureza Shore D 67 - ISO 7619-1
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 59 °C ISO 75-1/-2
Temp. reblandecimiento Vicat, A 147 °C ISO 306
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de humedad 0.4 % Sim. to ISO 62
Densidad 1250 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 60 °C -
Tiempo de pre-secado 2 h -
Temperatura del molde 30 - 55 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección, Otros tipos de extrusión
Forma de suministro
Sémola
Características
Cristalinidad alta
Certifications
Contiene recursos renovables, Biodegradables
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.