Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FORTRON® 0320 - PPS - Celanese

Material Data Center offers the following functions for FORTRON® 0320:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Fortron datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties
Any use of this information falls under the rules of our disclaimer.
Product Texts
0320 exhibits a high melt strength for extrusion processes. The material demonstrates excellent heat and chemical resistance. The intended use of this product is for extruding monofilament/fibers, rod and slab. Available standard in powder 'flake' (0320B0), ground powder (0320B0/100 µm), pellet (0320P0) and crystallized pellet (0320C0) form.

Flammability at thickness h (3 mm)V-0-
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Molding shrinkage, parallel 1.2 % ISO 294-4, 2577
Molding shrinkage, normal 1.5 % ISO 294-4, 2577
Spec. heat capacity of melt 1830 J/(kg K) -
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 3500 MPa ISO 527
Stress at break 90 MPa ISO 527
Strain at break 8 % ISO 527
Thermal propertiesValueUnitTest Standard
ISO Data
Melting temperature, 10°C/min 280 °C ISO 11357-1/-3
Glass transition temperature, 10°C/min 90 °C ISO 11357-1/-2
Temp. of deflection under load, 1.80 MPa 115 °C ISO 75-1/-2
Temp. of deflection under load, 8.00 MPa 95 °C ISO 75-1/-2
Coeff. of linear therm. expansion, parallel 52 E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion, normal 53 E-6/K ISO 11359-1/-2
Burning Behav. at thickness h V-0 class IEC 60695-11-10
Thickness tested 3.0 mm -
Electrical propertiesValueUnitTest Standard
ISO Data
Relative permittivity, 1MHz 4.6 - IEC 62631-2-1
Dissipation factor, 1MHz 11 E-4 IEC 62631-2-1
Volume resistivity 1E9 Ohm*m IEC 62631-3-1
Electric strength 18 kV/mm IEC 60243-1
Other propertiesValueUnitTest Standard
Water absorption 0.02 % Sim. to ISO 62
Density 1350 kg/m³ ISO 1183
Characteristics
Processing
Injection Molding, Fiber Extrusion, Film Extrusion, Profile Extrusion, Sheet Extrusion, Other Extrusion
Delivery form
Pellets, Powder
Special Characteristics
Heat stabilized or stable to heat
Features
Melt Strength
Chemical Resistance
General Chemical Resistance
Applications
Monofilament
Regional Availability
North America, Europe, Asia Pacific, South and Central America
Other text information
Injection molding
In spite of the minimum moisture absorption a drying of FORTRON is necessary. Predrying in a dehumidified air dryer at 120 degC/3-4 hours is recommended.
On injection molding machines with 15-25 D long three-section screws, are usual in the trade, the unreinforced FORTRON is processable. A shut-off nozzle is recommended.

Melt temperature 310-320 degC
Mold wall temperature at least 140 degC

A medium injection rate is normally preferred. All mold cavities must be effectively vented.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.