Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Bakelite® PF 1141 - PF-(GF+X) - Bakelite Synthetics

Check here, which other Bakelite datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Test specimen production - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

Product description:

Phenolic moulding compound, inorganically/organically filled, glass fibre reinforced, increased heat resistance, hot steam and hot water resistant (Not suitable for use of higher voltage).

Application areas:

Fittings for ovens and dishwashers, medium heat resistant cookware fittings.

Property Name	Value	Unit	Standard No.
Apparent density (moulding compound)	0.78	g/cm³	ISO 60
Moulding shrinkage (injection moulding, longitudinal)	0.6	%	ISO 2577
Post shrinkage (injection moulding, 168h/110°C)	0.3	%	ISO 2577
Compr. strength (test spec. flat tested)	200	MPa	ISO 604
Flexural strength (2mm/min)	90	MPa	ISO 178
Flexural modulus	8500	MPa	ISO 178
Ball indentation hardness (H 961/30)	350	MPa	ISO 2039/P1
Water absorption (24h/23°C)	20	mg	similar to ISO 62

Additional characteristics:

high surface quality, resistant to high temperature, dishwasher prrof

Preparation of Test Specimens of Thermosetting Moulding Compound

• Compression to ISO 295
• Injection to ISO 10724

Storage capability
2 years (relative humidity of 50-60% and maximum storage temperature of approximately 20°C)

Processing/Physical Characteristics	Value	Unit	Test Standard
ISO Data
Molding shrinkage, parallel	0.6	%	ISO 294-4, 2577

Mechanical properties	Value	Unit	Test Standard
ISO Data
Charpy impact strength, +23°C	6	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	1.8	kJ/m²	ISO 179/1eA

Thermal properties	Value	Unit	Test Standard
ISO Data
Temp. of deflection under load, 8.00 MPa	140	°C	ISO 75-1/-2

Electrical properties	Value	Unit	Test Standard
ISO Data
Relative permittivity, 100Hz	12	-	IEC 62631-2-1
Dissipation factor, 100Hz	0.15	E-4	IEC 62631-2-1
Volume resistivity	1E9	Ohm*m	IEC 62631-3-1
Surface resistivity	1E10	Ohm	IEC 62631-3-2
Electric strength	5	kV/mm	IEC 60243-1

Other properties	Value	Unit	Test Standard
Density	1520	kg/m³	ISO 1183

Test specimen production	Value	Unit	Test Standard
ISO Data
Injection Molding, injection temperature	115	°C	ISO 10724
Injection Molding, injection velocity	170	mm/s	ISO 10724
Injection Molding, hold pressure	100	MPa	ISO 10724
Injection Molding, cure time	25	min	ISO 10724
Compression Molding, mold temperature	160	°C	ISO 295
Compression Molding, cure time	1	min	ISO 295

Diagrams

Characteristics

Processing

Injection Molding, Transfer Molding

Regional Availability

North America, Europe, Asia Pacific, South and Central America, Near East/Africa

Other text information

Injection molding

VERARBEITUNG 

Temperature of material:	80 - 100	°C
Mould temperature:	160 - 190	°C
Curing time:	10-20	sec
Further Information:
Barrel temperature
- Feed zone:	60-75	°C
- Nozzle zone:	80-100	°C
Cavity moulding pressure:	>15	MPa
Back pressure:	0.5-2	MPa
Holding pressure:	60% of injection pressure

Compression molding

PROCESSING

Mould temperature:	160-190	°C
Curing time:	20-40	sec
Cavity moulding pressure:	>15	MPa

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.