Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Badalon® PC 20 - PC - Bada AG

Material Data Center offers the following functions for Badalon® PC 20:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Badalon datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 21 cm³/10min ISO 1133
Temperature 300 °C -
Load 1.2 kg -
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 2400 MPa ISO 527
Yield stress 62 MPa ISO 527
Yield strain 6 % ISO 527
Nominal strain at break 118 % ISO 527
Flexural modulus, 23°C 2400 MPa ISO 178
Flexural strength 95 MPa ISO 178
Charpy impact strength, +23°C N kJ/m² ISO 179/1eU
Charpy impact strength, -30°C N kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 60 kJ/m² ISO 179/1eA
Charpy notched impact strength, -30°C 12 kJ/m² ISO 179/1eA
Izod notched impact strength, +23°C 62 kJ/m² ISO 180/1A
Izod notched impact strength 12 kJ/m² ISO 180/1A
Temperature -30 °C -
Ball indentation hardness 115 MPa ISO 2039-1
Thermal propertiesValueUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 122 °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 136 °C ISO 75-1/-2
Vicat softening temperature, A 140 °C ISO 306
Vicat softening temperature, B 142 °C ISO 306
Coeff. of linear therm. expansion, parallel 65 E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion, normal 65 E-6/K ISO 11359-1/-2
Burning behav. at 1.5 mm nom. thickn. V-2 class IEC 60695-11-10
Thickness tested 1.5 mm -
Burning behav. at thickness h V-2 class IEC 60695-11-10
Thickness tested 3.0 mm -
GWIT - thickness tested (1) 850 mm -
Glow Wire Ignition Temperature (GWIT) 2 °C IEC 60695-2-13
Electrical propertiesValueUnitTest Standard
ISO Data
Relative permittivity, 1MHz 3.1 - IEC 62631-2-1
Dissipation factor, 1MHz 5 E-4 IEC 62631-2-1
Volume resistivity 1E12 Ohm*m IEC 62631-3-1
Surface resistivity 1E16 Ohm IEC 62631-3-2
Electric strength 17 kV/mm IEC 60243-1
Comparative tracking index 275 - IEC 60112
Other propertiesValueUnitTest Standard
Water absorption 0.32 % Sim. to ISO 62
Humidity absorption 0.2 % Sim. to ISO 62
Density 1200 kg/m³ ISO 1183
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 120 °C -
Pre-drying - Time 3 h -
Processing humidity ≤0.02 % -
Melt temperature 280 - 320 °C -
Mold temperature 80 - 120 °C -
Characteristics
Processing
Injection Molding
Special Characteristics
U.V. stabilized or stable to weather, Heat stabilized or stable to heat
Regional Availability
North America, Europe, Asia Pacific, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.