Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of TECACOMP® POM TRM natural 3758 - (POM+PTFE+SI) - Ensinger Compounds

Material Data Center offers the following functions for TECACOMP® POM TRM natural 3758:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Tecacomp datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 热性能 - 电性能 - 其它性能 - 加工推荐（注塑）
Any use of this information falls under the rules of our disclaimer.
加工/物理特性价值单位Test Standard
ISO数据
熔体体积流动速度, MVR 1.5 cm³/10min ISO 1133
温度 190 °C -
载荷 2.16 kg -
熔融指数, MFI 1.5 g/10min ISO 1133
温度 190 °C -
负载 2.16 kg -
模塑收缩率, 平行 2.8 % ISO 294-4, 2577
模塑收缩率, 垂直 2.5 % ISO 294-4, 2577
机械性能价值单位Test Standard
ISO数据
拉伸模量 2500 MPa ISO 527
拉伸强度 60 MPa ISO 527
断裂伸长率 25 % ISO 527
简支梁缺口冲击强度, +23°C 8 kJ/m² ISO 179/1eA
热性能价值单位Test Standard
ISO数据
熔融温度, 10°C/min 175 °C ISO 11357-1/-3
玻璃化转变温度, 10°C/min -60 °C ISO 11357-1/-2
热变形温度, 1.80 MPa 115 °C ISO 75-1/-2
热变形温度, 0.45 MPa 170 °C ISO 75-1/-2
线性热膨胀系数, 平行 121 E-6/K ISO 11359-1/-2
线性热膨胀系数, 垂直 117 E-6/K ISO 11359-1/-2
厚度为h时的燃烧性 HB class IEC 60695-11-10
电性能价值单位Test Standard
Other Standards[S]
体积电阻率 4.5E13 Ohm*m IEC 61340-2-3
表面电阻率 6.6E13 Ohm IEC 61340-2-3
S: These properties are reported by the producer according standards that are different to our defaults.
其它性能价值单位Test Standard
吸湿性 0.2 % 类似ISO 62
密度 1430 kg/m³ ISO 1183
Bulk density 680 kg/m³ -
加工推荐（注塑）价值单位Test Standard
预干燥-温度 80 - 100 °C -
预干燥-时间 3 - 4 h -
加工湿度 ≤0.2 % -
注塑熔体温度 210 - 220 °C -
模具温度 80 - 100 °C -
1区 180 - 220 °C -
典型数据
加工方法
注塑
供货形式
粒料, 自然色
添加剂
润滑剂
特征
Tribologic Grade, 均聚物
应用
汽车
地区供应
北美, 欧洲, 亚太, 中南美洲
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.