Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Excelloy AK15 (AK102) - (ABS+PA*) - Techno-UMG Co., Ltd.

Material Data Center offers the following functions for Excelloy AK15 (AK102):
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Excelloy datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 其它性能 - 加工推荐（注塑）
Any use of this information falls under the rules of our disclaimer.
加工/物理特性干 / 已调节单位Test Standard
ISO数据
熔融指数, MFI 30 g/10min ISO 1133
温度 260 °C -
负载 10 kg -
模塑收缩率, 平行 0.8 / * % ISO 294-4, 2577
机械性能干 / 已调节单位Test Standard
ISO数据
拉伸强度 41 / 30 MPa ISO 527
弯曲模量, 23°C 1610 / 680 MPa ISO 178
弯曲强度 59 / 32 MPa ISO 178
简支梁冲击强度, +23°C 69 / 76 kJ/m² ISO 179/1eU
洛克硬度 R 101 - ISO 2039-2
ASTM数据
拉伸强度 42.2 / 30.4 MPa ASTM D 638
弯曲模量 1960 / 900 MPa ASTM D 790
弯曲强度 67.7 / 40.2 MPa ASTM D 790
洛克硬度 R 102 / R 91 - ASTM D 785
其它性能干 / 已调节单位Test Standard
密度 1060 / - kg/m³ ISO 1183
密度 1060 kg/m³ ASTM D 792
加工推荐（注塑）价值单位Test Standard
预干燥-温度 80 - 90 °C -
预干燥-时间 2 - 5 h -
模具温度 40 - 80 °C -
1区 240 - 280 °C -
典型数据
加工方法
注塑
特殊性能
高冲击韧性的/经抗冲改性的
耐化学试剂
通用耐化学性
应用
电子电气
地区供应
北美, 亚太
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.